Yamaha S90 Manual download pdf (Page 84)

Basics Section Quick Guide Reference Appendix

Using Memory Cards

■ File types that can be loaded from the

Memory Card to the S90 when turning the

power on (Auto Load ﬁle)

Among the ﬁle types described on page 83, “All”,

“Plugin All Bulk 1”, “Plugin All Bulk 2” and “Plugin

All Bulk 3” can be loaded from the Memory Card to the

S90’s User Memory automatically when turning the

power on.

Data will be loaded automatically and any existing data

in memory will be overwritten, therefore, you should

save important data to Memory Card beforehand.

1 Name the ﬁles you wish to have load automatically

when the power is turned on as described below,

and save them together in a single folder.

n After you’ve ﬁnished naming the appropriate ﬁles,

keep the corresponding folder selected in the display

and go to step

2 Press the [UTILITY] button to enter the Utility

mode.

3 Press the [F1] button, then press the [SF4] button to

show the Auto Load ﬁle display.

4 Set “Auto Load” to on, and press the [SF5] button.

5 To apply the newly made parameter settings, exit

from the Utility mode.

Never attempt to turn off the power while data is being

written to Flash ROM (while an “Executing...” or

“Please keep power on” message is shown). Turning

the power off in this state results in loss of all user data

and may cause the system to freeze (due to corruption

of data in the Flash ROM).

6 Turn the power off.

7 Before turning the power on next time, make sure

that the appropriate data is available to the S90. In

other words, make sure Memory Card speciﬁed in

step 1 is properly inserted.

8 Turn the power on. The S90 searches the speciﬁed

folder for the auto-load ﬁles (the ﬁles you named

and saved in step 1), and automatically loads them

to User memory.

n Any ﬁles in the folder registered in step 4 that do

not have appropriate auto-load names are ignored.

■ File names

Files are named according to the MS-DOS naming

convention. If the ﬁle name contains spaces and other

characters unrecognized in MS-DOS, these characters

will automatically be replaced by “_” (underscore)

characters when saving.

For speciﬁc instructions on naming ﬁles, see page 34.

[F1] Formatting Memory

Cards (FORMAT)

The explanations here apply to step 2 of the Basic

Procedure on page 83.

Before you can use a new Memory Card with the S90,

you will need to format it. Use this operation to format

the memory card and assign a Volume Label to it.

While formatting is in progress, do not eject the Memory

Card or turn off the power to the S90.

If data is already saved on the memory card, be careful

not to format it. If you format the memory card, all the

previously recorded data will be deleted.

1 Name the Volume Label. For instructions on

naming, see page 34 in the “Basic Operations”

section.

2 Press the [ENTER] button. (The display prompts

you for conﬁrmation.)

n To cancel the Format operation, press the [DEC/NO]

button.

3 Press the [INC/YES] button to execute the Format

operation. After formatting has been completed, a

“Completed” message appears and operation

returns to the original display.

File type File name

All AUTOLOAD.W4A

Plugin All Bulk 1

(for slot 1)

AUTOLD1.W2B

Plugin All Bulk 2

(for slot 2)

AUTOLD2.W2B

Plugin All Bulk 3

(for slot 3)

AUTOLD3.W2B

Set this to on.

Press the [SF5] button to register the folder selected in step

#1 (the folder containing the desired ﬁles for auto loading).

1 2 ... 79 80 81 82 83 84 85 86 87 88 89 ... 138 139

Comments to this Manuals

No comments

Yamaha S90 Manual Page 84

Comments to this Manuals