Yamaha S90 Manual Page 101
- Page / 139
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
101
Basics SectionQuick GuideReferenceAppendix
70
PitchSens
Pitch Key Follow Sensitivity
Determines the sensitivity of the Key Follow effect (the interval of adjacent notes). At +100, adjacent notes are pitched one semitone
(100 cents) apart. At 0, all notes are the same pitch (for the percussion sounds,etc.). At +50, one octave is stretched out over twenty-
four notes. For negative values, the settings are reversed.
*28
71
CenterKey
Pitch Key Follow Center
Key
Determines the basic pitch (note number) used by the PitchSens parameter (above). The note number in this setting is the same
pitch as normal (100%).
*28
*12
72
EGTimeSens
PEG Time Key Follow
Sensitivity
Determines the sensitivity of the PEG time (the speed of the PEG change) to velocity.
*28
73
CenterKey
PEG Time Key Follow
Center Key
Determines the basic pitch (note number) used by the EGTimeSens parameter (above). When the center note is played, the PEG
time behaves according to its actual settings. For other notes, the speed varies in proportion to the key played and its interval away
from the center key.
*28
*12
74
Bank
Arpeggio Type Bank
Determines the Arpeggio bank.
pre1: preset 1, pre2: preset 2, user: User Arpeggio data (page 83) saved by MOTIF series (when loaded from a Memory Card)
45 *29
75
Type
Arpeggio Type
Determines the Arpeggio type. The two-letter prefix before the name indicates the general Arpeggio category.
45
*29
*34
76
Tempo
Arpeggio Tempo
Determines the Arpeggio Tempo. When MIDI sync (Utility [F5]→[SF3]) is turned on, “MIDI” is displayed here and cannot be set. In
the Sequence Play mode, the tempo is synchronized to that of the song (page 76).
45
77
Switch (ArpSwitch)
Arpeggio Switch
Determines whether Arpeggio is on or off. You can control the switch by using the Foot Switch (Utility [F4]→[SF3] FS=96).
45 *30
78
Hold
Arpeggio Hold
Determines whether Arpeggio playback is “held” or not. When set to “on,” the Arpeggio cycles automatically, even if you release
your fingers from the keys, and it continues to cycle until the next key is pressed. You can control this setting by using the Foot
Switch (Utility [F4]→[SF3] FS=97).
45 *31
79
KeyMode
Arpeggio Key Mode
Determines how the Arpeggio plays back when playing the keyboard.
*32
*33
*34
80
VelMode
Arpeggio Velocity Mode
Determines the playback velocity of the Arpeggio, or how it responds to your own playing strength.
*35
81
NoteLimit
Arpeggio Note Limit Low/
High
Determines the lowest and highest notes in the Arpeggio’s note range.
*36
*12
82
VelocityLimit
Arpeggio Velocity Limit
Low/High
Determines the lowest and highest velocity in the Arpeggio’s velocity range. This lets you control when the Arpeggio sounds by your
playing strength.
47 *13
83
UnitMultiply
Arpeggio Unit Multiply
Adjust the Arpeggio playback time. For example, if you set a value of 200%, the playback time will be doubled and the tempo
halved. If you set a value of 50%, the playback time will be halved and the tempo doubled.
84
VelocityRate
Arpeggio Velocity Rate
Determines how much the Velocity of the Arpeggio playback is offset from the original value. For example, a setting of 100% means
the original values are used.
*37
*38
85
GateTimeRate
Arpeggio Gate Time Rate
Determines how much the Gate Time (length) of the Arpeggio notes is offset from the original value. A setting of 100% means the
original values are used.
*37
86
OutputSwitch
Arpeggio MIDI Out Switch
When set to on, Arpeggio playback data is output from the MIDI terminal.
*39
87
TransmitCh
Arpeggio MIDI Transmit
Channel
Determines the MIDI transmit channel for Arpeggio playback data.
KbdCh...Arpeggio playback data is transmitted by KBDTransCh ([F5]→[SF1] Keyboard Transmit Channel) in the Utility mode
(Performance/Mixing)
88
BC/AS1/AS2/
FC1/FC2
BC/Assign1/Assign2/FC1/
FC2
Control Number
Sets the control number for the Breath Controller (BC), Assign 1/2 sliders (AS1/2), and Foot Controllers 1/2 (FC1/2).
53 *40
89
(Transmit Switch)
Transmit Switch
When the relevant parameter is set to “on,” playing the selected zone will transmit the corresponding MIDI data, such as Control
Change and Program Change messages. Pressing the [F5] button switches between display of all four Zones and one single Zone
(in which all transmit channel settings are shown). In the four-Zone display, use the cursor buttons to scroll.
90
Type
Filter Type
Determines the filter type. The parameters differ depending on the selected type.
63 *41
Ref.
#
Display
Parameter Name
Explanation
Related
Page
- MUSIC SYNTHESIZER 1
- SPECIAL MESSAGE SECTION 2
- IMPORTANT SAFETY INSTRUCTIONS 3
- PRECAUTIONS 4
- About This Manual 7
- Application Index 8
- Table of Contents 11
- The Controls & Connectors 12
- Rear Panel 13
- Setting Up 14
- Connections 15
- Connecting External MIDI 16
- Equipment 16
- Connecting to a Personal 17
- Computer 17
- Connecting Various 18
- Controllers 18
- Demo Playback 19
- Overview of the S90 20
- Plug-in board line-up 21
- Maximum Polyphony 22
- ● Voice mode 23
- ● Performance mode 23
- Card Drive/Sequencer 24
- Voices & Performance 25
- Voice & Element 26
- Performance 26
- GM Voices 27
- Internal Memory 28
- Memory Card 28
- Basic Operations 29
- Selecting a Mode 30
- Display Indications 30
- Selecting Functions 32
- How to leave the 32
- [ENTER] button 32
- Display-based Controls 33
- Naming (Entering Characters) 34
- Using the Character List 35
- Relative) 35
- Playing Voices 36
- 3 Select a Voice Group 37
- 4 Select a Voice number 37
- 5 Play the keyboard 37
- DEC/NO INC/YES 38
- EXIT ENTER 38
- Voice editing in the 39
- Voice Play mode 39
- (Quick Edit) 39
- Playing Performances 41
- Layering Voices (Parts) 42
- Together (Layer) 42
- Splitting the Keyboard 42
- Editing 44
- Performances in the 44
- Performance Play 44
- Using the Arpeggio function 45
- F2F1 F3 F4 F5 F6 46
- SF1 SF2 SF3 SF4 SF5 46
- INFORMATION 46
- Using as a Master Keyboard 48
- Playing the Master Demo 49
- (Selecting Masters) 49
- Using Zones — 51
- Creating a Layer/ 51
- Split with an external 51
- 7 Store the settings to a 52
- Master (page 73) 52
- 5 Call up the TRANS display 52
- 6 Call up the NOTE display 52
- Using Controllers 53
- Footswitch (assignable) 54
- ON/OFF ON/OFF ON/OFF ON/OFF 55
- MIDI Control 56
- Controller Set 56
- Using the Remote 58
- Control function 58
- Remote Control Assignments 59
- Voice Edit 60
- Performance Edit mode 61
- 4 Set the Element Parameters 62
- About the Filter types 63
- Resonance 64
- 6 Storing Edited Voices 66
- Using Effects 67
- Effect connection 68
- ● In the Performance mode: 69
- Using the Jobs 70
- Edit Recall [F2] 71
- Using the Copy function [F3] 71
- Factory Set (Restore Factory 72
- Defaults) 72
- Saving the Settings (Store) 73
- Playing the Songs 75
- Moving the Song position/ 76
- Changing the Tempo 76
- Mixing mode 77
- Mixing Edit mode (Detailed 79
- Mixer functions) 79
- Piano Voice 80
- (sequencer software) 80
- Bass Voice 80
- Drum Voice 80
- Using Memory Cards 82
- File/Folder selection 83
- New Folder Creation 83
- File types that can be 83
- [F1] Formatting Memory 84
- Cards (FORMAT) 84
- [F2] Saving the S90 data to 85
- Memory Card (SAVE) 85
- [F3] Loading the S90 Data 85
- [F4] Renaming the Files 86
- (RENAME) 86
- [F5] Deleting the Files 86
- (DELETE) 86
- Touch Sensitivity 87
- Function Tree 88
- Parameter Table 92
- SF5 SF5 40 99 93
- (F3→Selected 96
- Parameter/Function List 97
- Reference (Function List) 98
- (VelSensOfs) 99
- Related 100
- Utility ([F3]→ [SF1]) 108
- Freq (Frequency) 109
- Q (Frequency Characteristic) 109
- Speed = fast 112
- Speed = slow 112
- Keyboard 113
- Generator 113
- External MIDI Device 113
- Information Displays 114
- Utility mode 115
- Card mode 115
- Master mode 115
- Display Messages 116
- Messages Information 117
- About MIDI 118
- MIDI Messages Transmitted/ 119
- Received by the S90 119
- CHANNEL MESSAGES 119
- Channel Mode Messages 121
- SYSTEM MESSAGES 122
- Installing Optional Hardware 123
- Optional Plug-in 124
- Board Installation 124
- CATEGORY 125
- Optional mLAN8E 126
- Installation 126
- 4). If 127
- Troubleshooting 128
- Plug-in board does not work 130
- Specifications 131
- FCC INFORMATION (U.S.A.) 138
- OWNER’S MANUAL 139
© 2020, manymanuals.com. All rights reserved. | 0.728 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals