Yamaha S90 Manual download pdf (Page 105)

105

Basics SectionQuick GuideReferenceAppendix

155

(FEG) Attack/Decay/

Release (Time)

FEG Attack/Decay/Release

Time

Set the FEG (Filter Envelope Generator)/AEG (Amplitude Envelope Generator) parameters for each part. The parameters offset the

same parameters in Voice Element Edit (F3]→[SF3]/[F4]→[SF3]).

*53

156

(FEG) Sustain

(Level)

FEG Sustain Level

157

(AEG) Attack/Decay/

Release (Time)

AEG Attack/Decay/Release

Time

*54

158

(AEG) Sustain

(Level)

AEG Sustain Level

159

Wave

LFO Wave

Determines the LFO waveform used to vary the sound.

user...applies the user wave you edited on the Voice Editor (see the separate Installation Guide). For details, see the Voice Editor

Owner’s Manual (PDF).

66 *55

160

Speed

LFO Speed

Determines the speed of the LFO waveform. The higher the value, the faster the speed.

*56

161

TempoSync

LFO Tempo Sync

Determines whether or not the LFO is synchronized to the tempo of the Arpeggio or sequencer (song).

162

TempoSpeed

LFO Tempo Speed

Allows you to make detailed note value settings that determines how the LFO pulses in sync with the Arpeggio or sequencer when

the TempoSync parameter above is set to on.

*57

163

KeyOnReset

Key On Reset

Determines whether or not the LFO is reset each time a note is pressed. Three settings are available (Voice Edit Common).

*58

164

Phase

LFO Phase

Determines the starting phase point for the LFO Wave when a note is played.

*59

165

(KeyOn)Delay

LFO (Key On) Delay Time

Determines the delay time before the LFO comes into effect.

*60

166

FadeIn

LFO Fade-in Time

Determines the amount of time for the LFO effect to fade in (after the Delay time has elapsed). A higher value results in a slower

fade-in.

167

Hold

LFO Hold Time

Determines the length of time during which the LFO is held at its maximum level.

168

FadeOut

LFO Fade-out Time

Determines the amount of time for the LFO effect to fade out (after the Delay time has elapsed).

169

ElementSw

LFO Destination Element

Switch

Determines whether or not each element is to be affected by the LFO. The element number (1 - 4) is shown when the LFO is

enabled; a dash (-) indicates the LFO is disabled for that element.

170

Dest

LFO Destination

Determines the parameters which are to be controlled (modulated) by the LFO Wave.

171

Depth

LFO Depth

Determines the LFO Wave Depth.

172

PMod (LFO)

LFO Pitch Modulation

Depth

Determines the amount (depth) by which the LFO waveform varies (modulates) the pitch of the sound.

173

FMod (LFO)

LFO Filter Modulation

Depth

Determines the amount (depth) by which the LFO waveform varies (modulates) the Filter Cutoff frequency.

174

AMod (LFO)

LFO Amplitude Modulation

Depth

Determines the amount (depth) by which the LFO waveform varies (modulates) the amplitude of the sound.

175

(Part Receive

Switch)

Part Receive Switch

Set how each individual part responds to various MIDI messages, such as Control Change and Program Change messages.

*61

176

BasicRcvCh

Basic Receive Channel

Determines the MIDI channel over which the S90 receives MIDI data (from an external MIDI equipment. This parameter is available

for the Voice/Performance mode. When this is set to “omni,” the data of any channel can be received.

*62

177

KBDTransCh

Keyboard Transmit

Channel

(Voice/Performance Mode)

Determines the MIDI channel over which the S90 sends MIDI data (to an external MIDI device). This parameter is available for the

Voice /Performance mode.

178

DeviceNo./DEV NO.

Device No.

Determines the MIDI Device Number. This number must match the Device Number of the external MIDI device when transmitting/

receiving system exclusive messages.

Ref.

Display

Parameter Name

Explanation

Page

1 2 ... 100 101 102 103 104 105 106 107 108 109 110 ... 138 139

Comments to this Manuals

No comments

Yamaha S90 Manual Page 105

Comments to this Manuals