Yamaha S90 Manual Page 120
- Page / 139
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
120
Basics Section Quick Guide Reference Appendix
About MIDI
Sostenuto (Control #066)
Messages which control sostenuto on/off.
Holding specific notes and then pressing and holding the
sostenuto pedal will sustain those notes as you play
subsequent notes, until the pedal is released.
Setting the value between 64 -127 turns the sostenuto on,
between 0 - 63 turns the sostenuto off.
Harmonic Content (Control #071)
Messages which adjust the filter resonance set for each
Part.
The value set here is an offset value which will be added
to or subtracted from the voice data.
Higher values will result in a more characteristic,
resonant sound.
Depending on the voice, the effective range may be
narrower than the range available for adjustment.
Release Time (Control #072)
Messages which adjust the AEG release time set for each
Part.
The value set here is an offset value which will be added
to or subtracted from the voice data.
Attack Time (Control #073)
Messages which adjust the AEG attack time set for each
Part.
The value set here is an offset value which will be added
to or subtracted from the voice data.
Brightness (Control #074)
Messages which adjust the filter cutoff frequency set for
each Part.
The value set here is an offset value which will be added
to or subtracted from the voice data.
Lower values will result in a softer sound.
Depending on the voice, the effective range may be
narrower than the range available for adjustment.
Decay Time (Control #075)
Messages which adjust the AEG decay time set for each
Part. The value set here is an offset value which will be
added to or subtracted from the voice data.
Effect1 Depth (Reverb Send Level)
(Control #091)
Messages which adjust the send level for the Reverb effect.
Effect3 Depth (Chorus Send Level)
(Control #093)
Messages which adjust the send level for the Chorus effect.
Data Increment (Control #096)
Decrement (Control #097) for RPN
Messages which increase or decrease the MSB value of
pitch bend sensitivity, fine tune, or coarse tune in steps of
1. You are required to assign one of those parameters
using the RPN in the external device in advance.
The data byte is ignored.
When the maximum value or minimum value is reached,
the value will not be incremented or decremented further.
(Incrementing the fine tune will not cause the coarse
tune to be incremented.)
NRPN (Non-Registered Parameter Number)
LSB (Control #098) (Plug-in Board only)
NRPN (Non-Registered Parameter Number)
MSB (Control #099) (Plug-in Board only)
Messages which adjust a voice’s vibrato, filter, EG, drum
setup or other parameter settings.
First send the NRPN MSB and NRPN LSB to specify the
parameter which is to be controlled. Then use Data Entry
(page 119) to set the value of the specified parameter.
Note that once the NRPN has been set for a channel,
subsequent data entry will be recognized as the same
NRPN’s value change. Therefore, after you use the
NRPN, you should set a Null (7FH, 7FH) value to avoid
an unexpected result.
For details, refer to the owner’s manual of the relevant
Plug-in Board.
- MUSIC SYNTHESIZER 1
- SPECIAL MESSAGE SECTION 2
- IMPORTANT SAFETY INSTRUCTIONS 3
- PRECAUTIONS 4
- About This Manual 7
- Application Index 8
- Table of Contents 11
- The Controls & Connectors 12
- Rear Panel 13
- Setting Up 14
- Connections 15
- Connecting External MIDI 16
- Equipment 16
- Connecting to a Personal 17
- Computer 17
- Connecting Various 18
- Controllers 18
- Demo Playback 19
- Overview of the S90 20
- Plug-in board line-up 21
- Maximum Polyphony 22
- ● Voice mode 23
- ● Performance mode 23
- Card Drive/Sequencer 24
- Voices & Performance 25
- Voice & Element 26
- Performance 26
- GM Voices 27
- Internal Memory 28
- Memory Card 28
- Basic Operations 29
- Selecting a Mode 30
- Display Indications 30
- Selecting Functions 32
- How to leave the 32
- [ENTER] button 32
- Display-based Controls 33
- Naming (Entering Characters) 34
- Using the Character List 35
- Relative) 35
- Playing Voices 36
- 3 Select a Voice Group 37
- 4 Select a Voice number 37
- 5 Play the keyboard 37
- DEC/NO INC/YES 38
- EXIT ENTER 38
- Voice editing in the 39
- Voice Play mode 39
- (Quick Edit) 39
- Playing Performances 41
- Layering Voices (Parts) 42
- Together (Layer) 42
- Splitting the Keyboard 42
- Editing 44
- Performances in the 44
- Performance Play 44
- Using the Arpeggio function 45
- F2F1 F3 F4 F5 F6 46
- SF1 SF2 SF3 SF4 SF5 46
- INFORMATION 46
- Using as a Master Keyboard 48
- Playing the Master Demo 49
- (Selecting Masters) 49
- Using Zones — 51
- Creating a Layer/ 51
- Split with an external 51
- 7 Store the settings to a 52
- Master (page 73) 52
- 5 Call up the TRANS display 52
- 6 Call up the NOTE display 52
- Using Controllers 53
- Footswitch (assignable) 54
- ON/OFF ON/OFF ON/OFF ON/OFF 55
- MIDI Control 56
- Controller Set 56
- Using the Remote 58
- Control function 58
- Remote Control Assignments 59
- Voice Edit 60
- Performance Edit mode 61
- 4 Set the Element Parameters 62
- About the Filter types 63
- Resonance 64
- 6 Storing Edited Voices 66
- Using Effects 67
- Effect connection 68
- ● In the Performance mode: 69
- Using the Jobs 70
- Edit Recall [F2] 71
- Using the Copy function [F3] 71
- Factory Set (Restore Factory 72
- Defaults) 72
- Saving the Settings (Store) 73
- Playing the Songs 75
- Moving the Song position/ 76
- Changing the Tempo 76
- Mixing mode 77
- Mixing Edit mode (Detailed 79
- Mixer functions) 79
- Piano Voice 80
- (sequencer software) 80
- Bass Voice 80
- Drum Voice 80
- Using Memory Cards 82
- File/Folder selection 83
- New Folder Creation 83
- File types that can be 83
- [F1] Formatting Memory 84
- Cards (FORMAT) 84
- [F2] Saving the S90 data to 85
- Memory Card (SAVE) 85
- [F3] Loading the S90 Data 85
- [F4] Renaming the Files 86
- (RENAME) 86
- [F5] Deleting the Files 86
- (DELETE) 86
- Touch Sensitivity 87
- Function Tree 88
- Parameter Table 92
- SF5 SF5 40 99 93
- (F3→Selected 96
- Parameter/Function List 97
- Reference (Function List) 98
- (VelSensOfs) 99
- Related 100
- Utility ([F3]→ [SF1]) 108
- Freq (Frequency) 109
- Q (Frequency Characteristic) 109
- Speed = fast 112
- Speed = slow 112
- Keyboard 113
- Generator 113
- External MIDI Device 113
- Information Displays 114
- Utility mode 115
- Card mode 115
- Master mode 115
- Display Messages 116
- Messages Information 117
- About MIDI 118
- MIDI Messages Transmitted/ 119
- Received by the S90 119
- CHANNEL MESSAGES 119
- Channel Mode Messages 121
- SYSTEM MESSAGES 122
- Installing Optional Hardware 123
- Optional Plug-in 124
- Board Installation 124
- CATEGORY 125
- Optional mLAN8E 126
- Installation 126
- 4). If 127
- Troubleshooting 128
- Plug-in board does not work 130
- Specifications 131
- FCC INFORMATION (U.S.A.) 138
- OWNER’S MANUAL 139
© 2020, manymanuals.com. All rights reserved. | 0.891 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals