Yamaha AW2816 Owner's Manual download pdf (Page 317)

315

Reference section

B NAME EDIT buttons

These buttons edit the name (maximum 8 charac-

ters) assigned to the fader/[ON] key. When you

move the cursor to these buttons and press the

[ENTER] key, a popup window will appear, allow-

ing you to input the name.

C LATCH/UNLATCH button

This button selects the mode of operation when

the [ON] key is pressed. Move the cursor to this

button and press the [ENTER] key to switch

between the following two modes of operation.

• LATCH

On/off will alternate each time you press the [ON]

key.

• UNLATCH

The state will be “on” only while you hold down

the [ON] key, and will be “off” when you release

it.

Tip!

Depending on whether you select Latch or Unlatch,

the operation of the [ON] key will be as follows.

• If “SW” is speciﬁed

• If “SW” is not speciﬁed

Tip!

Normally you will use the Unlatch mode when you do

not specify “SW.”

D LEARN button

When this button is turned on, the channel mes-

sage or system exclusive message received at the

MIDI IN/TO HOST connector will be input into

the MIDI message area (1). This function is conve-

nient since it allows MIDI messages received by

the AW2816 to be assigned directly (or with mod-

iﬁcations) to an [ON] key or fader.

Tip!

• Normally you will turn on only one of the [LEARN]

buttons.

• When a channel message or system exclusive is

received while the LEARN button is on, the byte fol-

lowing the last byte of the message will automatically

be set to “END.”

• If a system exclusive message longer than 16 bytes is

received while the LEARN button is on, the ﬁrst 16

bytes will be displayed.

• If the LEARN button for the fader is on, and a control

change message with continuously changing value is

received, the byte corresponding to the variable

value will automatically be set to “FAD.”

E ENABLE/DISABLE button

This button switches whether the Remote func-

tions of the currently displayed page will be

enabled (ENABLE) or disabled (DISABLE).

When you access the Remove A–Remote D pages

and switch this button to ENABLE, the correspond-

ing MIDI messages will be transmitted when you

operate the [ON] keys or faders.

Tip!

• You can enable/disable the remote function indepen-

dently for each of the Remote A–Remote D pages.

• The on/off state of the [ON] keys and the position of

the faders is remembered independently for each of

the Remote A–Remote D pages.

• The state of the faders/[ON] keys used by the Remote

function can be saved in a scene memory, or you can

record fader/[ON] key operations in automix. This

allows you to use the Remote A–D pages simulta-

neously.

F 1–8 buttons

These indicate channel numbers 1–8. The cur-

rently selected channel will be highlighted, and

the upper part of the display will show the MIDI

messages assigned to the [ON] key and fader of

that channel. Below each button, the name of the

[ON] key (upper line) and the name of the fader

(lower line) is shown for the corresponding chan-

nel.

To select a channel, you can press its [SEL] key,

move the cursor to a button 1–8 and press the

[ENTER] key, or directly operate an [ON] key or

fader.

dark darklit

MIDI data transmitted

(SW=7F)

MIDI data transmitted

(SW=00)

dark

LATCH

dark lit

MIDI data transmitted

(SW=7F)

MIDI data transmitted

(SW=00)

UNLATCH

MIDI data transmitted

darkdark lit

UNLATCH

REMOTE screen

1 2 ... 312 313 314 315 316 317 318 319 320 321 322 ... 419 420

Comments to this Manuals

No comments

Yamaha AW2816 Owner's Manual Page 317

Comments to this Manuals

Related products and manuals for Receiver Yamaha AW2816