Yamaha MTX3 Manual download pdf (Page 107)

“YDIF” screen (Cascade mode) Chapter 4. System screen

MTX Editor User’s Manual

107

❑ “YDIF” screen (Cascade mode)

This screen appears in Cascade mode. It indicates which MTX MATRIX bus is routed to which

YDIF output.

You can turn the YDIF outputs on or off in the [CASCADE MODE] section on the [OUTPUT] tab

of the “MTX Configuration” dialog box.

1 2 ... 102 103 104 105 106 107 108 109 110 111 112 ... 200 201

MTX Editor 1
User’s Manual 1
Contents 2
● Emergency mode 5
Data handled by MTX Editor 6
2on previous page) 8
4on previous page) 8
5 on previous page) 8
What are YDIF connections? 9
MTX Editor User’s Manual 10
What are Dante connections? 12
❑ About redundant networks 13
Patching 14
YDIF or Dante 15
Workflow 16
EXT. I/O screen 17
MAIN screen 17
“Input Patch” dialog box 18
Port select 18
“Preset” dialog box 19
Preset button 19
Save the project file 22
About the screens 23
Moving between screens 24
Title bar 25
Menu bar 25
Tool buttons 28
Chapter 3. Project screen 30
Network devices 31
MTX system 32
• [UNIT ID] box 36
•[YDIF MODE] 36
• [< Back] button 38
• [Next >] button 38
• [Finish] button 38
Identify button 39
• [Print] button 41
• [Close] button 41
❑ YDIF-connected devices 42
❑ Digital control panel 43
❑ Analog-connected devices 44
❑ DANTE-connected devices 45
[System] tab 46
[Device] tab 47
[Alert] tab 49
Screen select buttons 51
“MAIN” screen 53
Input channels 54
Stereo input channels 58
Effect return channels 59
Direct input channels 59
Output channels 60
❑ “Input Patch” dialog box 62
❑ “Output Patch” dialog box 63
“INPUT” screens 64
● Screen selection 65
“GAIN/HPF/EQ” screen 66
“GATE/COMP” screen 68
“FBS/AGC” screen 70
• AGC [ON] button 72
• [COMPENSATION LEVEL] knob 72
• [RESPONSE TIME] knob 72
• [NOISE GATE] button 72
“GAIN/EQ” screen 73
“COMP/AGC” screen 73
“MATRIX” screen 74
Send level 75
•[ON] button 76
Setting the input channel mix 77
“ZONE” screen 78
*1 DISTRIBUTION MODE only 82
• OSCILLATOR [ON] button 83
•WAVE FORM 83
• Output [LEVEL] knob 83
“OUTPUT” screens 84
“DELAY/ROOM EQ” screen 85
•ROOM EQ [ON] button 86
■ Pre-installed LIBRARY 87
■ [SP GRAPH] tab 87
■ [PEQ GRAPH] tab 88
■ CROSSOVER 89
■ [HIGH] tab/[LOW] tab 90
■ LIMITER 91
“EFFECT” screen 92
“DCA” screen 94
“MY4-AEC” screen 96
Common items 97
❑ “To Far-end” screen 99
❑ “Near-end Voice” screen 100
❑ “Mic” screen 101
“EXT. I/O” screen 102
“YDIF Out Patch” dialog box 104
“Channel Select” dialog box 104
“YDIF In Patch” dialog box 104
❑ “YDIF In Patch” dialog box 105
❑ “YDIF Out Patch” dialog box 105
❑ “Channel Select” dialog box 106
YDIF output 107
❑ “ANALOG” screen 108
❑ “Line Out Patch” dialog box 109
❑ “DANTE” screen 110
❑ “Dante In Patch” dialog box 111
“XMV” screen 112
Chapter 4. System screen 113
❑ “XMV Patch” dialog box 114
“EXo8” screen 115
❑ “EXo Patch” dialog box 116
• [To Device] option button 117
• [From Device] option button 117
• [OK] button 117
•[Cancel] button 117
• [Detail] button 118
Progress bar 119
Message area 119
Synchronization 121
Chapter 6. Presets 123
• [OFF]/[ON] toggle button 125
• Preset select box 125
“Preset Link” dialog box 126
“Settings” dialog box 127
MTX select buttons 128
■ “GPI Out” dialog box 129
■ “SD Play” dialog box 130
• [Interval Time] 132
Recall Filter setting screen 133
■ [Apply] button 134
■ [Close] button 134
■ [MTX] tab 134
“L” side 135
■ [External I/O] tab 137
Chapter 7. Dialog boxes 138
❑ “Network Setup” dialog box 139
•Battery 141
“Update Firmware” dialog box 142
■ Update procedure 143
“IP Address” dialog box 144
• INPUT PORT SETUP 146
• INPUT CHANNEL SETUP 146
•MATRIX BUS SETUP 147
• CASCADE MODE 147
• OUTPUT CHANNEL SETUP 147
❑ “Word Clock” dialog box 150
• [Word Clock Fs:] box 151
❑ “Clock” dialog box 152
• Start time 154
•End time 154
20:00 10:00 155
20:00 12:00 155
● [Month] button/[Day] button 156
• [Type] box 158
• Settings 158
If you chose Preset Recall 159
If you chose GPI Out 159
❑ “Remote Control” dialog box 163
❍ Control select buttons 166
❑ “Wireless DCP” dialog box 168
❑ “GPI” dialog box 169
<Usage example 3> 170
“Log on” dialog box 174
❑ “Get Log” dialog box 176
Appendix 178
■ Switch 179
•Input Ch Send ON 180
•Fx RTN Send ON 180
•SD Song Select & Play 180
•SD Song Pause 180
If [Play 1 song] is selected 181
❍ [MTX] 182
❍ [PARAMETER1]/[PARAMETER2] 182
✦[Upper Limit] 182
✦[Minimum] 182
■ Knob/Slider 185
•Input Ch Send Level 186
•Fx RTN Send Level 186
■ GPI Input 187
•Input Ch Level 189
•Fx RTN Level 189
•ZONE Out Level 189
■ GPI Output 191
• Closed 192
• Pulse Inv 192
Alert list 195
Alert list Appendix 196
Troubleshooting 200
409IP-D0 201

Comments to this Manuals

No comments

Yamaha MTX3 Manual Page 107

Comments to this Manuals

Related products and manuals for Processors Yamaha MTX3