Yamaha PSR-520 User Manual download pdf (Page 94)

100

101

*10 Exclusive

The following system exclusive parameters are supported.

<GM system ON> F0H, 7EH, 7FH, 09H, 01H, F7H

All parameters except MIDI master Tuning and Dsp setting are

reset to their default values.

Remote Channel setting is canceled.

This message requires approximately 50ms to execute, so

sufficient time should be allowed before the next message is

sent.

<DISK ORCHESTRA ON> F0H, 43H, 73H, 01H, 14H, F7H

This message switches PSR-520 to Disk Orchestra defualt

settings.

Remote Channel setting is canceled.

This message requires approximately 50ms to execute, so

sufficient time should be allowed before the next message is

sent.

<DISK ORCHESTRA OFF> F0H, 43H, 73H, 01H, 13H, F7H

This message switches Disk Orchestra ON to OFF.

All parameters except MIDI master Tuning are reset to their

default values.

This message requires approximately 50ms to execute, so

sufficient time should be allowed before the next message is

sent.

<MIDI Master Volume> F0H, 7FH, 7FH, 04H, 01H, ll, mm, F7H

Allows the volume of all channels to be changed simultane-

ously.

“mm” is used as the MIDI Master Volume value (“ll” is ignored).

The defalut value for “mm” is 7FH.

F0H, 43H, 1nH, 27H, 30H, 00H, 00H, mm, ll, cc, F7H

“mmll” is used as the MIDI Master Tuning value.

The tuning value is represented as follows:

T=M-128 (28<=M<=228), T=-100 (M<28), T=100 (M>228)

Where T is the actual tuning value in cents.

M is decimal value represented by 1-byte using bits 0..3 of

“mm” as the MSB and bits 0..3 of “ll” as the LSB.

The default values of “mm” and “ll” are 08H and 00H

resprectively.

n and cc are also recognized.

This value is not reset by a GM System ON or Reset All Con-

trollers message.

This value affects not only MIDI reception part but the entire

system of the PSR-520.

<Panel Voice> F0H, 43H, 76H, 1BH, cc, vv, F7H

This message alternately selects Panel voice or GM voice.

cc: MIDI channel

vv: 00=GM voice mode/01=Panel voice mode

GM voice mode is defalut.

This message is ignored by the remote channel.

Song Memory:

F0H, 43H, 76H, 1CH, bl, bh, <DATA>, cs, F7H

Multi Pad:

F0H, 43H, 76H, 1DH, bl, bh, <DATA>, cs, F7H

Registration Memory:

F0H, 43H, 76H, 1EH, bl, bh, <DATA>, cs, F7H

“bl” and “bh” represent the total byte count as “bl + bh*128”.

cs=Checksum.

<XG System On> F0H, 43H, 1nH, 4CH, 00H, 00H, 7EH, 00H, F7H

n: device number (transmission: n=0, reception: n is ignored.)

All parameters except MIDI master Tuning are reset to their

default values.

Remote Channel setting is canceled.

This message requires approximately 50ms to execute, so

sufficient time should be allowed before the next message is

sent.

F0H, 43H, 1nH, 4CH, aaH, bbH, ccH, ddH........F7H

n: device number(transmission: n=0, reception: n is ignored.)

aa,bb,cc: address High, Mid, Low (see below)

dd: data (succesive transmission and reception are possible

within the amount of data shown in the following Table-1)

Note: PSR-520 corresponds to XG parameters in the Table-1.

But this is a part of XG parameters, PSR-520 does not

perfectly correspond to XG format.

MIDI Implementation Chart / Implementierungstabelle / Table d’implémentation / Gráfico de implememtación

1 2 ... 89 90 91 92 93 94 95 96 97 98 99 100 101

Comments to this Manuals

No comments

Yamaha PSR-520 User Manual Page 94

Comments to this Manuals

Related products and manuals for Synthesizers Yamaha PSR-520