Yamaha RX-A2000 Owner's Manual download pdf (Page 47)

En 47

CONNECTIONS

Setting up the speaker parameters automatically (YPAO)

■

Message list

■ When a warning message is displayed before measurement

■ Error messages

■ Warning messages

NOTE

If the following messages appear, resolve the problems that have occurred and carry out the

measurement process again.

Connect MIC! The YPAO microphone is not connected. Connect the YPAO microphone to the YPAO

MIC jack on the front panel.

Unplug HP! The headphones are connected. Remove the headphones.

Memory Guard! The settings of this unit are protected. Set “Memory Guard” in the Setup menu to

“Off” (☞p. 108).

E-1:

No Front SP

The unit was not able to find the front channel. Check that the left and right front speakers are

connected correctly.

E-2:

No Sur. SP

The unit was only able to find one of side of the

surround channels.

Check that the left and right surround speakers

are connected correctly.

E-3:

No F.PRNS SP

The unit was only able to find one of side of the

presence channels.

Check that the left and right presence speakers

are connected correctly.

E-4:

SBR→SBL

Only one surround back speaker is connected

and only the right side surround back channel

sound is detected.

When only one surround back speaker is

connected, connect to the left side (SINGLE)

terminal.

E-5:

Noisy

The noise is too loud, preventing accurate

measurements from being taken.

Measure again in quiet surroundings. Turn off

any devices in the room that may be emitting

noise, or place them further away from the

YPAO microphone.

When this message is displayed, selecting

“PROCEED” will allow you to continue

measuring. However, we recommend resolving

the problem and measuring again, as continuing

measurement without doing so will not give

accurate results.

E-6:

Check Sur.

Even though surround left and right speakers

are not connected, only the surround back

speakers are connected.

When using surround back speakers, connection

of the surround left/right speakers is necessary.

E-7:

No MIC

The YPAO microphone has been removed. While measuring, take care not to touch the

YPAO microphone.

E-8:

No Signal

The YPAO microphone could not distinguish a

test tone.

Check that the YPAO microphone has been

installed correctly.

Check that each speaker has been connected

and installed correctly.

The YPAO microphone or the YPAO MIC jack

may be broken. Inquire at the retailer where

you purchased this unit, or the nearest Yamaha

service center.

E-9:

User Cancel

You have carried out an operation that has

cancelled the measuring process.

Carry out the measuring process again. Do not

operate this unit by, for example, adjusting the

volume.

E-10:

Internal Error

An internal error has occurred. Carry out the measuring process again. Contact

a Yamaha service center if “E-10” is displayed

again.

W-1:

Out of Phase

The speakers displayed are connected with the

opposite polarity. Depending on the type of

speakers you are using and the environment in

which you have them installed, this message

may occur even if the speakers are connected

correctly.

Depending on the type of speakers, “W-1” may

display even if the speakers are connected

correctly.

Check that the speaker polarity + (positive),

and - (negative) are correct. If these are

connected correctly, you can use the speakers

normally even this message appears.

W-2:

Over 24m/80ft

The speakers displayed are separated from the

listening position by more than 24 m, and

cannot be adjusted correctly.

Install the speakers with 24 m of the listening

position.

W-3:

Level Error

Volume level varies greatly for individual

channels, and cannot be adjusted correctly.

Check that all speakers are installed in the

same surroundings.

Check that the speaker polarity + (positive),

and - (negative) are correct.

We recommend the same speakers or speakers

with as similar specifications as possible.

Adjust the volume of the subwoofer.

If “W-2” or “W-3” appears, you can apply measurement results, but they will not give optimal

results. We recommend that you resolve the problem and carry out the measurement process again.

1 2 ... 42 43 44 45 46 47 48 49 50 51 52 ... 158 159

Comments to this Manuals

No comments

Yamaha RX-A2000 Owner's Manual Page 47

Comments to this Manuals

Related products and manuals for AV receivers Yamaha RX-A2000