Yamaha R-8 Owner's Manual Page 47
- Page / 128
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Troubleshooting
43 En
ADDITIONAL
INFORMATION
English
Refer to the chart below if this unit does not function properly. If the problem you are experiencing is not listed below or
if the instructions below do not help, set this unit to standby mode, disconnect the power cable, and contact the nearest
authorized Yamaha dealer or service center.
■ General
Troubleshooting
Problem Cause Remedy
See
page
This unit fails to turn
on.
The protection circuitry has been activated
three times consecutively. If the unit is in
this condition, the standby indicator on the
unit blinks when you try to turn on the
power.
As a safety precaution, capability to turn on the power
is disabled. Contact your nearest Yamaha dealer or
service center to request repair.
—
The power cable is not connected or the
plug is not completely inserted.
Connect the power cable firmly.
—
The impedance setting is incorrect. Set the impedance to match your speakers.
11
The protection circuitry has been activated
because of a short circuit, etc.
Check that the speaker wires are not touching each
other and then turn the power of this unit back on.
10
This unit has been exposed to a strong
external electric shock (such as lightning
or strong static electricity).
Set this unit to standby mode, disconnect the power
cable, plug it back in after 30 seconds, then use it
normally.
—
No sound Incorrect input or output cable
connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
10
No appropriate input source has been
selected.
Select an appropriate input source with the INPUT
selector on the front panel (or one of the input
selection keys on the remote control).
14
The SPEAKERS A/B switches are not set
properly.
Turn on the corresponding SPEAKERS A or
SPEAKERS B.
14
Speaker connections are not secure. Secure the connections.
10
Output has been muted. Turn off the mute.
8
The Max volume or Initial volume setting
is set too low.
Set the setting to a higher value.
36
The component corresponding to the
selected input source is turned off or is not
playing.
Turn the component on and make sure it is playing.
—
The audio output of a device connected to
a digital audio input (COAXIAL 1-2/
OPTICAL 1-2 jacks) is set to other than
PCM.
Set the audio output of the connected device to PCM.
—
The sound suddenly
goes off.
The protection circuitry has been activated
because of a short circuit, etc.
Set the speaker impedance to match your speakers.
11
Check that the speaker wires are not touching each
other and then turn the power of this unit back on.
10
This unit has become too hot. Make sure the openings on the top panel are not
blocked.
—
The auto power standby function has
turned this unit off.
Change the auto power standby (“AutoPowerStdby”
in the “SETUP” menu) to a longer setting or turn off.
37
Only the speaker on
one side can be
heard.
Incorrect cable connections. Connect the cables properly. If the problem persists,
the cables may be defective.
10
Incorrect setting for the BALANCE
control.
Set the BALANCE control to the appropriate
position.
15
ADDITIONAL INFORMATION
- Network Receiver 1
- Réseau Ampli-Tuner 1
- IMPORTANT SAFETY INSTRUCTIONS 2
- Contents 5
- Useful features 6
- Supplied accessories 7
- Controls and functions 10
- Using the remote controls 13
- Connections 14
- SPIMP.8MIN 15
- Connecting to a network 17
- Connecting power cable 17
- Playback 18
- VOLUME +/– 19
- Sleep120min 20
- FM98.5MHz 21
- 01:FM98.5MHz 22
- Connected 24
- ■ Repeat/shuffle settings 25
- (Example of English version) 28
- Song01 29
- Bookmarks 30
- JazzST 30
- RetryForgot 32
- QuickMix 33
- ArtistTrack 33
- Concerto 34
- Ilikeit 34
- Deleting Pandora stations 35
- Editing the Pandora accounts 35
- Track#1 36
- VolumeTrim 37
- NetworkSetup 38
- InitialVolume 38
- IniVol.+16.5dB 38
- Address1192 39
- NetworkName 40
- R-N500XXXXXX 40
- REMOTEIDID2 41
- INITCANCEL 42
- UPDATEUSB 42
- VERSIONxx.xx 42
- 3 Press TV A 43
- ■ Playback device operations 44
- 2 Press SETUP 45
- Troubleshooting 47
- ADDITIONAL 49
- INFORMATION 49
- ■ USB and network 50
- ■ Remote control 51
- Message Cause Remedy 52
- Trademarks 53
- Specifications 54
- Français 58
- Table des matières 61
- Fonctionnalités utiles 62
- Accessoires fournis 63
- Commandes et fonctions 64
- Utilisation des télécommandes 69
- Raccordements 70
- Remarque 72
- Raccordement à un réseau 73
- Raccordement du cordon 73
- Lecture d’une source 74
- 02:Empty 78
- ClearPreset 79
- 01:Cleared 79
- Configuration du partage de 84
- (AirPlay) 87
- Touches de curseur 91
- Enregistrement du code de 99
- Enregistrement des codes de 100
- 2 Appuyez sur SETUP 101
- NewFwAvailable 102
- PerformUpdate 102
- Guide de dépannage 103
- ■ Syntoniseur 105
- ■ USB et réseau 106
- ■ Télécommande 107
- Marques commerciales 109
- Caractéristiques techniques 110
- ❚ Information about software 113
- ❚ Information sur le logiciel 113
- ■ About JsonCpp 114
- ■ About Network 114
- ■ About PNG Reference Library 115
- ■ About RC4 Algorithm 116
- ■ About WPA Supplicant 116
- ■ About zlib Library 116
- LIST OF REMOTE CONTROL CODES 117
- LISTE DES CODES DE COMMANDE 117
- Blu-ray Disc 123
- DVD Recorder 123
- Satellite 124
Related products and manuals for Tuner Yamaha R-8
Tuner Yamaha T-S1000 Service Manual
(85 pages)
(85 pages)
Tuner Yamaha T-S500 User Manual
(11 pages)
(11 pages)
Tuner Yamaha T-S1000 User Manual
(3 pages)
(3 pages)
Tuner Yamaha N470D User Manual
(12 pages)
(12 pages)
Tuner Yamaha R-N602 Owner's Manual
(130 pages)
(130 pages)
© 2020, manymanuals.com. All rights reserved. | 0.139 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals