Yamaha Amp Editor Owner's Manual download pdf (Page 205)

Appendix

Amp Editor Owner’s Manual

205

—— 

Internal time

clock error

—013

A problem has occurred

with the internal clock, and

it has been initialized

(January 1, 2000, 0:00)

If this occurs each time you turn

on the power, it is possible that

the internal backup battery has

run down or that the device has

malfunctioned. Contact your

Yamaha dealer.

If this occurs only once, an

abnormality was detected with

the clock setting and it was

initialized; use Amp Editor to set

the time.

Fault Continual

—

Scene recall

error

Scene recall err —

The scene could not be

recalled.

It is likely that the device has

malfunctioned; immediately stop

using the device and contact

your Yamaha dealer.

Error Single



Duplicate IP

address

Duplicate IP adr 040

There is an IP address

conflict on the network.

Change the IP addresses so that

there are no duplicates.

Error Continual

—— 

IP address

setting error

—041

IP address was not set

within 60 seconds of

startup.

Please check rear panel DIP

switch 6 (IP Setting). If DIP

switch 6 is set to “PC,” use Amp

Editor or DHCP server to specify

the device IP address.

Warning Continual

—— 

Too many

devices on the

network

—043

Too many devices are

connected to the network.

Reduce the number of devices

connected to the network.

Error Single

— Network busy Network busy —

Due to heavy network

traffic, communication is

taking time.

Check the devices that are

connected to the network. If an

excessive number of devices are

connected, try reducing the

number of devices. Also make

sure that you are not connected

to the same network as an audio

network.

Information

Continual

—— 

The UNIT ID is

set to “00”

— 050 The UNIT ID is set to “00.”

Set the UNIT ID to something

other than “00.”

Error Continual

—— 

Duplicate UNIT

ID error

—051

Devices with identical

UNIT IDs were found

connected within the same

network.

Change the UNIT ID so that there

are no duplicates.

Error Continual

—  —

Amp

communication

error

Amp comm

error

—

A problem has occurred in

the transmission at [DATA

PORT] connector (0–31).

Make sure that each of the

connected amplifiers has a

unique ID.

Alternatively, a cable may be

shortcircuited or noise may be

affecting the connection.

Error Single

 — 

Word clock

unlocked

WCLK unlocked 021

The word clock master has

become unlocked.

Make sure that the word clock

signal is being input correctly.

This will also appear when you

switch the word clock.

Error Continual

—— 

YDIF sync error

(Single)

—022

The digital signal being

input to the [YDIF IN]

connector is not

synchronized to the word

clock of this device.

Make sure that YDIF cables are

properly connected.

Use cables that meet the

required specifications.

Error Single

—— 

YDIF sync error

(Continual)

—023

The digital signal being

input to the [YDIF IN]

connector is not

continuously synchronized

to the word clock of this

device.

Error Continual

—— 

YDIF input

connection error

—030

There is a problem with the

connection of the [YDIF

IN] connector.

Error Continual

 ——

Slot sync error

(Single)

SlotSyncErr

Sngl

—

The digital signal being

input to the slot is not

synchronized to the word

clock of this device

Either input a signal that is

synchronized, or specify the slot

as the word clock master.

Warning Single

 ——

Slot sync error

(Continual)

SlotSyncErr

Cntn

—

The digital signal being

put to the slot is not

continuously synchronized

to the word clock of this

device.

Information

Continual

TXn

ACD1

XMV

Message

(shown in

Amp Editor)

Message

(shown on

TXn/ACD1)

Alert number

(shown on

XMV)

Content Response Initial type

Single/

Continual

1 2 ... 200 201 202 203 204 205 206 207 208 209 210 211

Comments to this Manuals

No comments

Yamaha Amp Editor Owner's Manual Page 205

Comments to this Manuals

Related products and manuals for Software Yamaha Amp Editor