Yamaha RX-V863 User Manual Page 113
- Page / 274
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
TROUBLESHOOTING
111 En
ADDITIONAL
INFORMATION
English
Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized
Yamaha dealer or service center.
■ General
Troubleshooting
Problem Cause Remedy
See
page
This unit fails to turn
on or enters the
standby mode soon
after the power is
turned on.
The power cable is not connected or the
plug is not completely inserted.
Connect the power cable firmly. —
The speaker impedance setting is incorrect. Set the speaker impedance to match your speakers. 28
The protection circuitry has been activated. Make sure that all speaker wire connections on this
unit and on all speakers are secure and that the wires
for each connection do not touch anything other than
their respective connections.
14
This unit has been exposed to a strong
external electric shock (such as lightning or
strong static electricity).
Set this unit to the standby mode, disconnect the power
cable, plug it back in after 30 seconds and then use this
unit normally.
—
No sound. Incorrect input or output cable connections. Connect the cables properly. If the problem persists,
the cables may be defective.
20-26
The optimizer microphone is connected. Disconnect the optimizer microphone. 35
Audio input jack select is set to “HDMI”,
“COAX/OPT” or “ANALOG”.
Set Audio input jack select to “AUTO”. 44
Audio input jack select is set to
“ANALOG” while playing a source
encoded in Dolby Digital or DTS.
Set Audio input jack select to “AUTO” or
“COAX/OPT”.
44
No appropriate input source has been
selected.
Select an appropriate input source with the INPUT
selector on the front panel (or the input selector
buttons on the remote control).
42, 43
Speaker connections are not secure. Secure the connections. 14
The front speakers to be used have not been
selected properly.
Select the front speakers by pressing
A
SPEAKERS
on the front panel repeatedly.
43
The volume is turned down. Turn up the volume. —
The sound is muted.
Press
G
MUTE or
G
VOLUME +/– on the remote
control to resume audio output and then adjust the
volume.
45
Signals this unit cannot reproduce are
being input from a source component, such
as a CD-ROM.
Play a source whose signals can be reproduced by this
unit.
—
The HDMI components connected to this
unit do not support the HDCP copy
protection standards.
Connect HDMI components that support the HDCP
copy protection standards.
18
“S.AUDIO” is set to “OTHER” and
“HDMI” audio signals are not being played
back on this unit.
Set “S.AUDIO” to “RX-V863” in “MANUAL
SETUP”.
91
No picture. The output and input for the picture are
connected to different types of video jacks.
Set “VIDEO CONV.” to “ON” or connect your source
components in the same way as you connect your
video monitor to this unit.
88
Non-standard video signals are input.
The sound suddenly
goes off.
The protection circuitry has been activated
because of a short circuit, etc.
Check that the speaker impedance setting is correct. 28, 107
Check that the speaker wires are not touching each
other and then turn this unit back on.
—
The sleep timer has turned this unit off. Turn this unit on, and play the source again. —
The sound is muted.
Press
G
MUTE or
G
VOLUME +/– on the remote
control to resume audio output.
45
Sound is heard from
the speaker on one
side only.
Incorrect cable connections. Connect the cables properly. If the problem persists,
the cables may be defective.
14
Incorrect settings in “SP LEVEL”. Adjust the “SP LEVEL” settings. 79
- AV Receiver 1
- ■ For U.K. customers 2
- Contents 3
- Features 4
- Getting started 6
- Step 1: Set up your speakers 8
- ■ For further connections 9
- Step 3: Press SCENE 1 button 10
- Quick start guide 11
- Connections 12
- Placing speakers 13
- ■ 6.1-channel speaker layout 14
- ■ 5.1-channel speaker layout 14
- ■ Using presence speakers 15
- Connecting speakers 16
- PREPARATION 17
- 2 Loosen the knob 18
- ■ Audio jacks 19
- ■ Video jacks 19
- Information on HDMI™ 20
- Audio and video signal flow 21
- ■ Connecting a DVD player 23
- ■ Connecting a set-top box 24
- ■ Connecting audio components 25
- Open the lever 29
- Close the lever 29
- Turning this unit on and off 31
- Front panel display 32
- Using the remote control 33
- Using AUTO SETUP 34
- 5 Press 35
- 6 Press 35
- 7 Press 36
- 8 Press 36
- Selecting the desired SCENE 39
- Selecting the SCENE templates 40
- Creating your original SCENE 42
- Playback 44
- Selecting the MULTI CH INPUT 45
- Selecting audio input jacks 46
- Using your headphones 47
- Muting the audio output 47
- Playing video sources in the 47
- Displaying the input source 48
- Using the sleep timer 49
- Sound field programs 50
- ■ For various sources 51
- ■ For movie sources 51
- Enjoying unprocessed input 53
- Using audio features 54
- FM/AM tuning 55
- Using station preset feature 56
- 1 Press 59
- Using the enhanced other 60
- Using iPod™ 62
- Using Bluetooth™ components 64
- Recording 65
- Advanced sound configurations 67
- (“2ch Stereo” only) 71
- (“7ch Stereo” only) 71
- (“Straight Enhancer” and 71
- “7ch Enhancer” only) 71
- Selecting decoders 72
- Decoder parameter Features 73
- ■ Auto setup AUTO SETUP 74
- ■ Manual setup MANUAL SETUP 74
- Using SET MENU 78
- ■ Speaker level B)SP LEVEL 81
- ■ Test tone D)TEST TONE 82
- ■ Low-frequency effect level 85
- (lip sync) 86
- ■ Memory guard C)MEMORY GUARD 92
- ■ HDMI set E)HDMI SET 93
- Remote control features 94
- Setting remote control codes 96
- Programming codes from other 98
- Changing source names in the 99
- Macro programming features 100
- ■ Default macro functions 101
- 4 Press 102
- Clearing configurations 103
- 2 Press 104
- 3 Press and hold 104
- 3 Press 105
- 2 Press and hold 105
- Connecting Zone 2 106
- FRONT B/ZONE2/ 107
- PRESENCE 107
- EXTRA SP 107
- Advanced setup 109
- (remote control 110
- Troubleshooting 113
- Problem Cause Remedy 114
- ADDITIONAL 115
- INFORMATION 115
- ■ Tuner (FM/AM) 116
- ■ Remote control 117
- ■ Bluetooth 118
- ■ AUTO SETUP 119
- Resetting the system 121
- Glossary 122
- ■ Elements of a sound field 125
- ■ CINEMA DSP 125
- ■ SILENT CINEMA 125
- ■ Virtual CINEMA DSP 125
- ■ Compressed Music Enhancer 125
- Specifications 126
- ■ Numerics 128
- Содержание 135
- Описание 136
- Уведомление 137
- Подготовка 138
- Шаг 1: Установите колонки 140
- Шаг 2: Подключите DVD 141
- Шаг 3: Нажмите кнопку SCENE 1 142
- Для чего вам нужен данный 143
- Соединения 144
- Размещение колонок 145
- Подключение колонок 148
- ПОДГОТОВКА 149
- 2 Освободите головку 150
- ■ Аудиогнезда 151
- ■ Видеогнезда 151
- Информация о HDMI™ 152
- Поток аудио и видео сигнала 153
- ■ Подключение телеприставки 156
- Примечания 157
- SUBWOOFERFRONT 158
- SUR. BACKSURROUND 158
- SINGLE CENTER 158
- L R LRL R 159
- Использование гнезд 160
- VIDEO AUX на фронтальной 160
- Откройте рычажок 161
- Вставьте 161
- Закройте рычажок 161
- AC OUTLETS 162
- DVRMONITOR OUT 162
- Включение или отключение 163
- Дисплей фронтальной панели 164
- Использование пульта ДУ 165
- Использование AUTO SETUP 166
- 4 Нажимая 167
- 5 Нажимая 167
- 6 Нажимая 167
- 7 Нажимая 168
- 8 Нажмите 168
- 3 Нажмите 170
- Выбор нужного шаблона 171
- SCENE для кнопок SCENE 171
- Примечание 172
- Выбор шаблонов SCENE 173
- Создание своих оригинальных 174
- Установите на 175
- Кнопки SCENE 175
- Воспроизведение 176
- Выбор компонента MULTI 177
- CH INPUT 177
- Выбор фронтальной 177
- Выбор аудиовходных гнезд 178
- (AUDIO SELECT) 178
- Отображение текущего 178
- Аудиоисточники 179
- Видеоисточники 179
- Отображение информации 180
- Применение таймера сна 181
- Программы звукового поля 182
- ■ Для различных источников 183
- ■ Для киноисточников 183
- ■ Surround decode mode 184
- Прослушивание 185
- Использование аудиофункций 186
- Общий обзор 187
- Основные операции настройки 187
- Использование функции 188
- A1:FM 89.10MHz 189
- E1:FM 89.10MHz 190
- A5:FM 89.10MHz 190
- Выбор типа программы 191
- Системы Радиоданных 191
- (режим PTY SEEK) 191
- Использование информационной 192
- Использование iPod™ 194
- 1 Включите все подключенные 197
- 2 Поворачивая селектор 197
- [p]/[[]: 198
- REV.TIME 202
- REV.DELAY 202
- REV.LEVEL 202
- Выбор декодеров 204
- Использование SET MENU 210
- 1 BASIC MENU 211
- ■ Уровень громкости колонки 213
- Тестовый тональный сигнал 214
- 2 VOLUME MENU 215
- 3 SOUND MENU 216
- ■ Динамический диапазон 217
- 4 INPUT MENU 219
- 1 Нажимайте 220
- 2 Нажимая 220
- 4 Нажмите 220
- 1 Нажмите 221
- 4 Для выхода из 221
- 5 OPTION MENU 222
- [ENTER]: 223
- Исходная конфигурация 224
- ■ Установка HDMI E)HDMI SET 225
- Функции пульта ДУ 226
- TV VOL TV CH 227
- Установка кодов ДУ 228
- Программирование кодов 230
- Изменение названий 231
- Функции программирования 232
- ДОПОЛНИТЕЛЬНОЕ 233
- УПРАВЛЕНИЕ 233
- 2 Нажмите кнопку макроса для 234
- Удаление конфигураций 235
- 2 Нажмите 236
- 4 Для выхода, снова нажмите 236
- 3 Снова нажмите 237
- Подключение Zone 2 238
- Дополнительные настройки 241
- (настройка ДУ) 242
- (настройка 243
- ■ Общая часть 245
- Смотрите стр 246
- ДОПОЛНИТЕЛЬНАЯ 247
- ИНФОРМАЦИЯ 247
- ■ Тюнер (ЧM/AM) 248
- ■ Пульт ДУ 249
- Перезагрузка системы 253
- Справочник 254
- ■ Элементы звукового поля 257
- Технические характеристики 258
- ОБЩИЙ РАЗДЕЛ 259
- Предметный указатель 260
- AB CD E F G H I J 266
- KL M NO PQ R S 266
- Remote control/Пульт ДУ 267
- List of remote control codes 268
- APPENDIX 271
- RX-V863/RX-V663 273
- Printed in Malaysia 274
Related products and manuals for Receivers and Amplifiers Yamaha RX-V863
(271 pages)
(25 pages)© 2020, manymanuals.com. All rights reserved. | 4.371 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals