Yamaha RX-V3300 Manual download pdf (Page 31)

English

INTRODUCTION

PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONNECTIONSADJUSTING THE SPEAKER OUTPUT LEVELS

Notes

• If “1A CENTER SP” on the SET MENU is set to NONE, the

center channel sound is automatically output from the left and

right main speakers.

• If “1C REAR L/R SP” on the SET MENU is set to NONE, the

output level of the rear right, left and center speakers cannot be

adjusted in step 3. The test tone will be circulated in the order

of LEFT→CENTER→RIGHT→SUBWOOFER→LEFT...,

skipping the rear right and left speakers and the rear center

speaker.

• If “1D REAR CT SP” on the SET MENU is set to NONE, the

output level of the rear center speaker cannot be adjusted in

step 3. The test tone will be circulated in the order of

LEFT→CENTER→RIGHT→RIGHT SURROUND→LEFT

SURROUND→SUBWOOFER→LEFT ..., skipping the rear

center speaker.

• If “1E LFE/BASS OUT” on the SET MENU is set to MAIN,

the output level of the subwoofer cannot be adjusted. The test

tone will be circulated in the order of LEFT→CENTER→

RIGHT→RIGHT SURROUND→REAR CENTER→LEFT

SURROUND→LEFT…, skipping the subwoofer.

• It is not necessary to readjust the speaker level once it is set as

long as you do not change the speakers. You can enjoy listening

to or watching the input source with the desired volume by

adjusting the volume key.

• You can increase the output levels of the effect speakers

(center, left rear and right rear and rear center) to +10 dB. If the

output level of these speakers is lower than that of the main

speakers even after you have increased the output level of these

speakers up to +10 dB, set “1G MAIN LEVEL” on the SET

MENU to –10 dB (see page 64). This setting decreases the

main speaker output level to about one-third of the normal

level. After you have set “1G MAIN LEVEL” on the SET

MENU to –10 dB, adjust the levels for the center and rear

speakers again.

The test tone is heard from the left main speaker,

center speaker, right main speaker, right rear speaker,

rear center speaker, left rear speaker and subwoofer

in order. The tone is produced for 2.5 seconds each

time.

The state of the test tone output is also shown on the

monitor by an image of the audio listening room.

This is convenient for adjusting each speaker level.

Front panel display also indicates from which

speaker the test tone is output in the order of

TEST LEFT→TEST CENTER→TEST RIGHT→

TEST R SUR.→TEST REAR CNTR→TEST L SUR.

→TEST SUBWOOFER

Note

• If the test tone cannot be heard, turn down the volume, set this

unit in the standby mode and check the speaker connections.

3 Press –/+ repeatedly to

adjust the output level of

the effect speakers so that

the output level coming

from each speaker is the

same.

While adjusting, the test tone is heard from the

selected speaker.

Note

• Main L/R speaker level cannot be adjusted by itself. Use

VOLUME to adjust the main volume.

4 When the adjustment is

complete, press TEST.

To enter the “TEST DSP”

mode, press TEST once.

To stop the test tone, press

TEST twice.

LEFT

TEST DOLBY SUR.

LEFT SURROUND RIGHT SURROUND

CENTER

REAR CENTER

RIGHT LEFT

SUBWOOFER

TEST

0104V3300_24-28_EN(UA) 02.7.24, 6:05 PM27

1 2 ... 26 27 28 29 30 31 32 33 34 35 36 ... 94 95

Comments to this Manuals

No comments

Yamaha RX-V3300 Manual Page 31

Comments to this Manuals

Related products and manuals for Receiver Yamaha RX-V3300