Yamaha NX-S100S Owner's Manual download pdf (Page 3)

d) If the product does not operate normally by following 24

the operating instructions. Adjust only those controls

that are covered by the operating instructions as an

improper adjustment of other controls may result in

damage and will ofien require extensive work by a

qualified technician to restore the product to its normal

operation,

e) If the product has been dropped or damaged in any

way, and

I) When the product exhibits a distinct change in

perfk_rmance - this indicates a need for service.

20 Replacement Parts -- When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer or have the same

characteristics as the original part. Unauthorized

substitutions may result in fire, electric shock, or other

hazards.

21 SafEty Check ---Upon completion of any service or repairs

to this product, ask the service technician to pert_,mn safety

checks to determine that the product is in proper operating

condition.

22 Wall or Ceiling Mounting -- The unit should be mounted to

a wall or ceiling only as recommended by the manufacturer.

23 Heat -- The product should be situated away from heat

sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

Note to CATV system installer:

This _eminde_ is provided to call the CATV system installer's

attention to Article 820-40 of the NEC that provides

guidelines for proper grounding and, in particular, specifies

that the cable ground shall be connected to the grounding

system of the building, as close to the point of cable entry as

practical.

Outdoor Antenna Grounding = If an outside antenna or

cable system is connected to the product, be sure the

antenna or cable system is grounded so as to provide some

protection against voltage surges and builI-up static charges.

Article 810 of the National Electrical Code, ANSlYNFPA

70, provides information with regard to proper grounding of

the mast and supporting structure, grounding of the lead-in

wire to an antenna discharge unit, size of grounding

conductors, location of antenna discharge unit, connection

m grounding electrodes, and requirements fk_rthe

grounding electr(_e.

EXAMPLE OF ANTENNA GROUNDING

FCC INFORMATION (for US customers only)

1. IMPORTANT NOTICE : DO NOT MODIFY THIS

UNITI

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved

by Yamaha may void your authority, granted by the

FCC, to use the product.

2. IMPORTANT : When connecting this product to

accessories and/or another product use only high

quality shielded cables. Cable/s supplied with this

product MUST be used. Follow all installation

instructions. Failure to fMlow instructions could void

your FCC authorization to use this product in the USA.

3. NOTE : This product has been tested and found to

comply with the requirements listed in FCC

Regulations, Part 15 for Class "B" digital devices.

Compliance with these requirements provides a

reasonable level of assurance that your use of this

product in a residential environment will not result in

harmful interference with other electronic devices.

This equipment generates/uses radio f]-equencies and,

if not installed and used according to the instructions

f\)und in the users manual, may cause intertErence

harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee

that interference will not occur in all installations. If

this product is fkmnd to be the source of interference,

which can be determined by turning the unit "OFF" and

"ON", please try to eliminate the problem by using one

of the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line fiher/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon

lead, change the lead-in to coaxial type cable,

If these corrective measures do not produce satisfactory

resuhs, please contact the local retailer authorized to

dislribute this type of pr(_uct. If you can not locate the

appropriate retailer, please contact Yamaha Electronics

Corp., U.S.A. 6660 Omngethorpe Ave, Buena park, CA

90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

CAUTION

1 2 3 4 5 6 7 8 ... 81 82

Comments to this Manuals

No comments

Yamaha NX-S100S Owner's Manual Page 3

Comments to this Manuals

Related products and manuals for Receiver Yamaha NX-S100S