Yamaha R-N602 Owner's Manual Page 55
- Page / 66
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
51 En
English
ADDITIONAL
INFORMATION
ADDITIONAL INFORMATION
Refer to the chart below if this unit does not function properly. If the problem you are experiencing is not listed below or
if the instructions below do not help, set this unit to standby mode, disconnect the power cable, and contact the nearest
authorized Yamaha dealer or service center.
■ General
Troubleshooting
Problem Cause Remedy
See
page
The power does not
turn on.
The protection circuitry has been activated
three times consecutively. If the unit is in
this condition, the standby indicator on the
unit blinks when you try to turn on the
power.
As a safety precaution, capability to turn on the power
is disabled. Contact your nearest Yamaha dealer or
service center to request repair.
—
The power cable is not connected or the
plug is not completely inserted.
Connect the power cable firmly.
—
The protection circuitry has been activated
because of a short circuit, etc.
Check that the speaker wires are not touching each
other and then turn the power of this unit back on.
12
The internal microcomputer has frozen,
due to an external electric shock (such as
lightning or excessive static electricity) or
to a drop in the power supply voltage.
Turn OFF the A (Power) on the front panel and turn it
ON again after at least 15 seconds elapse. (If the
problem persists, disconnect the power cable from the
AC wall outlet and plug it again.)
—
The power does not
turn off.
The internal microcomputer has frozen,
due to an external electric shock (such as
lightning or excessive static electricity) or
to a drop in the power supply voltage.
Turn OFF the A (Power) on the front panel and turn it
ON again after at least 15 seconds elapse. (If the
problem persists, disconnect the power cable from the
AC wall outlet and plug it again.)
—
No sound. Incorrect input or output cable
connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
11
No appropriate input source has been
selected.
Select an appropriate input source with the INPUT
selector on the front panel (or one of the input
selection key on the remote control).
21
The SPEAKERS A/B switches are not set
properly.
Turn on the corresponding SPEAKERS A or
SPEAKERS B.
21
Speaker connections are not secure. Secure the connections.
11
Output has been muted. Turn off the mute.
9
The Max volume or Initial volume setting
is set too low.
Check the settings for “Max Volume” and “Initial
Volume” in the “Setup” menu.
47
The component corresponding to the
selected input source is turned off or is not
playing.
Turn the component on and make sure it is playing.
—
The audio output of a device connected to
a digital audio input (COAXIAL/
OPTICAL jacks) is set to other than PCM.
Set the audio output of the connected device to PCM.
—
The sound suddenly
goes off.
The protection circuitry has been activated
because of a short circuit, etc.
Set the speaker impedance to match your speakers.
48
Check that the speaker wires are not touching each
other and then turn the power of this unit back on.
12
This unit has become too hot. Make sure the openings on the top panel are not
blocked.
—
The auto power standby function has
turned this unit off.
Change the auto power standby (“AutoPowerStdby”
in the “Setup” menu) to turn off.
47
- Network Receiver 1
- ■ For U.K. customers 3
- Contents 5
- INTRODUCTION 6
- Supplied accessories 8
- Controls and functions 9
- NIHGED J KLMF 10
- Front display 11
- Rear panel 12
- Remote control 13
- ■ Installing batteries 14
- ■ Operation range 14
- Connections 15
- ■ Connecting via banana plug 16
- ■ Bi-wire connection 16
- ■ Connecting speaker cables 16
- PREPARATION 17
- Connecting the network cable 18
- Preparing a wireless antenna 18
- Connecting power cable 18
- Connecting to network 19
- R-N602 XXXXXX 20
- Wireless(WAC) 20
- USB cable 21
- WPA2-PSK(AES) 22
- Cursor keys 24
- (Pure Direct) 25
- BASS TREBLE 26
- VOLUMELOUDNESS 26
- VOLUME +/– 26
- Sleep 120min 27
- FM 98.50MHz 28
- Auto Preset 29
- 01:FM 87.50MHz 29
- 01:FM 98.50MHz 29
- 02:Empty 29
- Clear Preset 30
- 01:Cleard 30
- Program Type 31
- CLASSICS 31
- TP FM101.30MHz 31
- Connected 32
- Disconnecting a Bluetooth 33
- This unit 34
- Playback keys 35
- B / C / D / E 35
- ■ Repeat/shuffle settings 36
- Bookmarks 37
- 3 Access the vTuner website 38
- Check this box 40
- Track #1 43
- Track #1 45
- 01:Empty 46
- ■ Volume Trim 47
- ■ Signal Info 47
- Max Volume 48
- ■ Connection 49
- ■ Information 49
- ■ IP Address 49
- ■ DMC Control 49
- ■ Standby (Network Standby) 49
- Network Name 50
- Initial Volume 51
- AutoPowerStdby 51
- (Auto Power Standby) 51
- ECO Mode 51
- SP IMP.••8¬MIN 52
- REMOTE ID•AUTO 52
- INIT••••CANCEL 52
- ■ Firmware update procedure 53
- Available 54
- Perform Update 54
- ■ General 55
- Troubleshooting 56
- ADDITIONAL 57
- INFORMATION 57
- ■ Bluetooth 58
- ■ USB and network 59
- ■ Remote control 60
- Trademarks 62
- Specifications 63
Related products and manuals for Car media receivers Yamaha R-N602
Car media receivers Yamaha R-N500 Manual
(120 pages)
(120 pages)
Car media receivers Yamaha R-N803 Owner's Manual
(216 pages)
(216 pages)
(76 pages)
Car media receivers Yamaha R-N602 Owner's Manual
(507 pages)
(507 pages)
Car media receivers Yamaha R-N602 Owner's Manual
(130 pages)
(130 pages)
© 2020, manymanuals.com. All rights reserved. | 0.142 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals