Yamaha YST-SW1500 Manual download pdf (Page 15)

English

E-13

VOLUME control

VOLUME UP/DOWN buttons

Adjust the volume level. Turn the control clockwise or

press the UP button to increase the volume.

Turn the control counterclockwise or press the DOWN

button to decrease the volume.

To adjust the control on the front panel, put a coin, etc.

in the groove on the control and turn it.

5 Remote control sensor

Receives signals from the remote control.

6 Power indicator (LED)

Lights up in green while the subwoofer is turned on.

Lights up in red when the subwoofer is turned into the

standby mode by the automatic power-switching

function.

7 MUSIC/MOVIE indicator (LED)

Lights up in red when the MUSIC mode is selected,

and in green when the MOVIE mode is selected.

8 PHASE indicator (LED)

Lights up in red when the PHASE button (J) is set in

the regular mode, and in green when it is set in the

reverse mode.

9 PRESET 1/2/3 indicators (LED)

Show which PRESET number (1, 2 or 3) is selected.

(If the subwoofer is turned into the standby mode when

one of these indicators are illuminated, no indicator will

light up next time the subwoofer is turned on.)

0 AC IN

<U.S.A., Canada, Europe and Korean models only>

Plug the included power cable into this socket. Never

connect a power cable other than the included one to

this socket. Also, never connect the included power

cable to another unit.

A POWER switch

Normally, set this switch to the ON position to use the

subwoofer. In this state, you can turn on the subwoofer

or turn the subwoofer into the standby mode by

pressing the STANDBY/ON (1) button. Set this switch

to the OFF position to completely cut off the

subwoofer’s power supply from the AC line.

B REMOTE terminals

These terminals are used for custom installation

system. When the subwoofer is connected to the

components for custom installation system, you can

operate the subwoofer with the system remote control.

C AUTO STANDBY (HIGH/LOW/OFF) switch

This switch is originally set to the OFF position. By

setting this switch to the HIGH or LOW position, the

subwoofer’s automatic power-switching function

operates as described on page 14. If you do not need

this function, leave this switch in the OFF position.

D GND terminal

Connecting this terminal to ground (GND) terminal of

the receiver/amplifier can reduce a humming noise.

(See page 10.)

E H.P.F. (High Pass Filter) OUTPUT switch

Selects the upper limit of the frequencies to be cut off

from the signals outputted at the H.P.F. OUTPUT

terminals. Use this switch only when the H.P.F.

OUTPUT terminals are used for connecting with the

amplifier. (See page 8 for details)

H.P.F. OUTPUT terminals

These terminals cut off frequencies below the

frequency point selected by the H.P.F. OUTPUT switch

from the input signals and output higher frequencies.

F INPUT3 (LFE) terminals

The HIGH CUT control (3) has no effect on the signals

inputted to these terminals. (See page 5 for details)

G INPUT2 terminals

Used to input line level signals from the amplifier.

(Refer to “CONNECTIONS” for details.)

H OUTPUT (TO SPEAKERS) terminals

Can be used for connecting to the main speakers.

Signals are sent directly from the amplifier to the main

speakers by way of these terminals.

(Refer to “CONNECTIONS” for details.)

I INPUT1 (FROM AMPLIFIER) terminals

Used to connect the subwoofer with the speaker

terminals of the amplifier.

(Refer to “CONNECTIONS” for details.)

J PHASE button

Normally press this button to select the reverse mode.

However, according to your speaker systems or the

listening condition, there may be a case when better

sound quality is obtained by selecting the regular

mode. Select the better mode by monitoring the sound.

In the reverse mode, the PHASE indicator on the front

panel lights up in green, and in the regular mode, it

lights up in red.

K MEMORY button/PRESET buttons

Used to store and recall the data for the B.A.S.S.

[MUSIC/MOVIE] (2), the VOLUME [VOLUME UP/

DOWN] (4), the HIGH CUT [HIGH CUT UP/DOWN]

(3) and the PHASE (J) adjustments. (See page 16.)

2-SW1500(E) (02.9.2)a 02.9.3, 9:29 AM13

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 142 143

Comments to this Manuals

No comments

Yamaha YST-SW1500 Manual Page 15

Comments to this Manuals

Related products and manuals for Musical Instrument Amplifier Yamaha YST-SW1500