Yamaha MDX-595 Owner's Manual download pdf (Page 29)

English

TROUBLESHOOTING

If your MD recorder fails to operate normally, check the following table. It lists common operating errors and simple

measures which you can take to correct the problem. If it cannot be corrected, or the symptom is not listed, disconnect the

recorder’s power cord and contact your authorized YAMAHA dealer or service center for help.

Cause

• MD is dirty or damaged.

• MD is damaged (“UTOC ERR appears

in the display).

• There is an influence of strong external

noise (lightning, excessive static

electricity, etc.) or a misoperation was

performed while using this unit.

• Moisture is on the laser pickup.

• The power is OFF.

• The disc has been loaded incorrectly.

• An unrecorded (blank) MD was loaded

(“Blank Disc” appears in the display) .

• The disc is record protected

(“Protected” appears in the display).

• A pre-mastered MD is loaded

(“Playback MD” appears in the display).

• The source is not connected correctly.

• The input setting is incorrect.

• The recording level is too low.

• The digital output level of the digital

source is too low.

• There is not enough blank space left on

the MD.

• If the power cord was unplugged or

there was a power outage during

recording, that recording may be lost.

• The carriage lock function has activated.

• The unit is too close to the television or

other component.

• The batteries are exhausted.

• The remote control transmitter is

operated from an incorrect distance or

angle.

• The remote control sensor is located in

strong direct light.

Remedy

• Replace the current disc with a new

one.

• Turn the power off and disconnect the

AC power from the AC outlet. After

about 30 seconds have passed,

connect the power and try again.

• Leave the unit switched ON and wait 20

to 30 minutes for the moisture to

evaporate before trying to play a disc.

• Press POWER to turn the power on.

• Reload the disc with the label side

facing up, and the arrow pointing

toward the disc insertion slot.

• Insert a recorded MD.

• Slide the record-protect tab to the

closed position.

• Load a recordable MD.

• Check all connections again.

• Press INPUT repeatedly to select the

correct input jacks.

• Turn REC LEVEL to adjust the recording

level.

• Set the digital output level of the digital

source to “MAX”.

• Load a recordable MD with fewer

recorded tracks, or erase unnecessary

tracks from the current MD.

• If recording was interrupted, try

recording again starting from the

beginning.

• Insert the MD completely, then press

) EJECT to eject it.

• Place the unit farther away from the

television or other component.

• Replace the batteries.

• Operate the remote from less than 6

meters (about 20 feet) and within 30° on

either side of the sensor.

• Place the unit away from the strong

light.

Symptom

The unit does not respond to

operations.

It happens that this unit does not work

normally.

Playback is not possible.

Recording is not possible.

The MD cannot be removed when

partially inserted.

Excessive noise.

The remote control does not operate.

To clean the cabinet

Use a soft cloth slightly moistened with mild detergent solution.

Care of MDs

• Do not expose the MD to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight

as there can be a considerable rise in temperature inside the car.

• Periodically remove dust and debris from the cartridge surface by wiping it with a dry cloth.

• Because the MD itself is housed in a cartridge, you can handle it normally without being concerned about dirt or

fingerprints. However, malfunctioning may result if the cartridge itself is dirty or warped.

Do not open the shutter on the MD cartridge

Trying to force the shutter open will damage the shutter.

1 2 ... 24 25 26 27 28 29 30 31 32

Comments to this Manuals

No comments

Yamaha MDX-595 Owner's Manual Page 29

Comments to this Manuals

Related products and manuals for Minidisc players Yamaha MDX-595