Yamaha S03 User Manual download pdf (Page 20)

1.3 Channel mode messages

These messages specify the basic operation of a part.

1.3.1 All Sound Off

This message silences all currently-sounding notes on the corresponding channel.

However, the settings of channel messages such as Hold 1 and Sostenuto will be

maintained.

Control# Parameter Data Range

120 All Sound Off 0

1.3.2 Reset All Controllers

This message resets the following controllers to their default values.

The following data is not changed.

Parameter values specified by program change, bank select MSB/LSB, volume, pan, effect

send levels 1, 3, 4, RPN and NRPN.

Control# Parameter Data Range

121 Reset All Controllers 0

1.3.3 All Note Off

This message turns off all notes which are currently on for the corresponding part.

However, if Hold 1 or Sostenuto are on, notes will continue to sound until these are turned

off.

Control# Parameter Data Range

123 All Note Off 0

1.3.4 Omni Off

Perform the same processing as when All Note Off is received.

Control# Parameter Data Range

124 Omni Off 0

1.3.5 Omni On

Perform the same processing as when All Note Off is received.

Control# Parameter Data Range

125 Omni On 0

1.3.6 Mono

Perform the same processing as when All Sound Off is received, and if the value (mono

number) is in the range of 0...16, set the corresponding channel to Mode4* (m = 1).

Control# Parameter Data Range

126 Mono 0...16

*Mode4 is a state in which only channel messages on the specified channel will be

received, and notes will be sounded individually (monophonically).

1.3.7 Poly

Perform the same processing as when All Sound Off is received, and set the

corresponding channel to Mode3*.

Control# Parameter Data Range

127 Poly 0

*Mode3 is when channel messages will be received only on the specified channel, and will

be sounded polyphonically.

1.4 Program change

This message reports sound selection changes and changes the program number of the

receiving channel.

In order to include changes to the voice bank, Program Change and Bank Select

messages must be sent as a set (see 1.2.1).

When RevPROGRAM CHANGE = OFF for Multi Part Parameter, the program change for

that part is not received.

Not received when Receive Program Change in Native System Parameters is set to off.

1.5 Pitch bend

This message conveys movements of the pitch bender.

This message is generally used to modify the pitch of a part, but the depth of the following

seven effects can be controlled.

The effect of this message can be modified by the following parameters.

• Multi Part Parameter

1. BEND PITCH CONTROL

2. BEND FILTER CONTROL

3. BEND AMPLITUDE CONTROL

4. BEND LFO PMOD DEPTH

5. BEND LFO FMOD DEPTH

6. BEND LFO AMOD DEPTH

• Effect1 Parameter

7. BEND VARIATION CONTROL DEPTH

(Valid when Variation Effect is assigned to a part as Insertion)

By default, the Pitch Control effect is applied.

If the receive channel is a drum part, effects 5 and 6 will not apply.

If the Multi Part parameter Rcv PITCH BEND CHANGE = OFF, that part will not receive

pitch bend messages.

1.6 Channel aftertouch (Receive only)

This message conveys the pressure which is applied to the keyboard after playing a note

in order to create tonal changes (for an entire MIDI channel).

The pressure can be controlled for each part. This message will affect the currently-

sounding notes.

The effect of this message will be determined by the settings of the following parameters.

• EMulti Part Parameter

1. CAT PITCH CONTROL

2. CAT FILTER CONTROL

3. CAT AMPLITUDE CONTROL

4. CAT LFO PMOD DEPTH

5. CAT LFO FMOD DEPTH

6. CAT LFO AMOD DEPTH

• Effect1 Parameter

7. CAT VARIATION CONTROL DEPTH

(Valid when the Variation Effect is assigned to a part as Insertion)

By default, there will be no effect.

If the receive channel is a drum part, effects 5 and 6 will not apply.

If the Multi Part parameter Rcv CHANNEL AFTER TOUCH = OFF, that part will not receive

Channel Aftertouch.

1.7 Polyphonic aftertouch (Receive only)

This message conveys the pressure that is applied to the keyboard after playing a note (for

individual note numbers).

The pressure can be controlled independently for each note. This message will affect

currently-sounding notes.

The effect of this message is determined by the following Multi Part parameters.

1. PAT PITCH CONTROL

2. PAT FILTER CONTROL

3. PAT AMPLITUDE CONTROL

4. PAT LFO PMOD DEPTH

5. PAT LFO FMOD DEPTH

6. PAT LFO AMOD DEPTH

By default, there will be no effect.

The effect will apply to note numbers 36...97.

In the case of either of the following Multi Part parameter settings, that part will not receive

Polyphonic Aftertouch.

Rcv CHANNEL AFTER TOUCH = OFF

PART MODE = DRUM, DRUMS1, 2

2. System exclusive messages

2.1 Parameter changes

This devices uses the following parameter changes.

[UNIVERSAL REALTIME MESSAGE]

1) Master Volume

[UNIVERSAL NON REALTIME MESSAGE]

1) General MIDI System On

[XG PARAMETER CHANGE]

1) XG System on

2) XG System parameter change

3) Multi Effect1 parameter change

4) Multi Part parameter change

5) Drums Setup parameter change

[NATIVE PARAMETER CHANGE]

1) Native System parameter change

2) Remote Switch parameter change

3) Normal Voice parameter change

4) Drum Voice parameter change

[Others]

1) Master tuning

Controller Value

Pitch bend change ±0 (center)

Channel Aftertouch 0 (off)

Polyphonic Aftertouch 0 (off)

Modulation 0 (off)

Expression 127 (maximum)

Hold 0 (off)

Portamento 0 (off)

Sostenuto 0 (off)

Soft pedal 0 (off)

Portamento control

Reset the portamento source note number that was received.

RPN Number unset, internal data is not affected.

NRPN Number unset, internal data is not affected.

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 26 27 28

Comments to this Manuals

No comments

Yamaha S03 User Manual Page 20

Comments to this Manuals

Related products and manuals for Musical Instruments Yamaha S03