Yamaha S03 User Manual download pdf (Page 19)

1.2.16 Portamento Control

This message specifies the portamento source key number (the key number at which

portamento will begin).

Data of 0...127 specifies the portamento source key.

When Portamento Control is received, the currently-sounding pitch will change at a

Portamento Time of 0 to the key of the next-received note-on of the same channel.

Control# Parameter Data Range

84 Portamento Control 0...127

(C-2...G8)

This is received even if Rcv PORTAMENTO = OFF.

1.2.17 Effect1 Depth (Reverb Send Level)

This message specifies the send level for the reverb effect.

Control# Parameter Data Range

91 Effect1 Depth 0...127

Increasing this value will produce a richer reverb. The effect of the value will depend on the

state of the reverb effect.

1.2.18 Effect3 Depth (Chorus Send Level)

This message specifies the send level for the chorus effect.

Control# Parameter Data Range

93 Effect3 Depth 0...127

Raising this value will increase the modulation or spaciousness. The effect of the value will

depend on the state of the chorus effect.

1.2.19 Effect4 Depth (Variation Effect Send Level)

This message specifies the send level for the variation effect.

Control# Parameter Data Range

94 Effect4 Depth 0...127

However, this is not received if the Variation Effect parameter Variation Connection = 0

(Insertion).

1.2.20 Data Increment/Decrement (for RPN)

This message increases or decreases the parameter value specified for RPN (see 1.2.22),

by increments of 1.

Control# Parameter Data Range

96 RPN Increment --

97 RPN Decrement --

The data byte is ignored.

1.2.21 NRPN (Non-registered parameter number)

This message is used to specify a sound parameter (such as vibrato, filter, EG, drum setup

etc.) as an offset value.

Use NRPN MSB and NRPN LSB to specify the parameter that you wish to modify, and

then use Data Entry (see 1.2.4) to set the value for the specified parameter.

Control# Parameter Data Range

98 NRPN LSB 0...127

99 NRPN MSB 0...127

If the Multi Part parameter Rcv NRPN = OFF, that part will not receive NRPN.

The following NRPN messages can be received.

MSB 14H - 1FH (for drums) is received when Multi Part parameter PART MODE =

DRUMS1, 2.

*1 Refer to 1.2.4

*2 '--' indicates that the setting value is ignored.

*3 Adjusts the time after the note is played until vibrato begins to take effect. The effect

will begin more quickly for higher values, and more slowly for higher values.

1.2.22 RPN (Registered parameter number)

This message is used to specify part parameters such as Pitch Bend Sensitivity or Tuning

etc. as an offset value.

Use RPN MSB and RPN LSB to specify the parameter that you wish to modify, and then

use Data Entry (see 1.2.4) to set the value of the specified parameter.

Control# Parameter Data Range

100 RPN LSB 0...127

101 RPN MSB 0...127

If the Multi Part parameter Rcv RPN = OFF, that part will not receive this message.

The following RPN messages can be received.

*1 Refer to 1.2.4

*2 '--' indicates that the setting value is ignored.

1.2.23 Assignable controller

By assigning a control change number of 0...95 to a part, the specified effect can be

controlled.

This device allows two control change numbers (AC1 and AC2) to be specified for each

part.

The following parameters specify the effect of AC1 and AC2.

• Multi Part Parameter

1. AC1, AC2 PITCH CONTROL

2. AC1, AC2 FILTER CONTROL

3. AC1, AC2 AMPLITUDE CONTROL

4. AC1, AC2 LFO PMOD DEPTH

5. AC1, AC2 LFO FMOD DEPTH

6. AC1, AC2 LFO AMOD DEPTH

• Effect1 Parameter

7. AC1, AC2 VARIATION CONTROL DEPTH

(Valid if Variation Effect is assigned to a part as Insertion)

The AC1 control change number is specified by the Multi Part parameter AC1

CONTROLLER NUMBER, and the AC2 control change number is specified by the Multi

Part parameter AC2 CONTROLLER NUMBER.

NRPN

MSB LSB

Data Entry

MSB LSB Parameter name and value range

01H 08H mm --

Vibrato rate