Yamaha PSR-2700 Owner's Manual download pdf (Page 69)

| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

VRepeat as Necessary .............................................................................................................................

Repeat the above procedure to record the remaining SAMPLE PADS, as

required.

NOTES

• The PSR-2700 has 1,020 kilobytes (1.02 megabytes) of waveform

RAM memory for sampled voice storage. To find out how much of this

memory is available for recording press the [CLEAR] button: “XXXX

KByteFree” will appear on the display (“XXXX” indicates the remaining

RAM in kilobytes).

• The sample data is retained in memory even when the power switch is

turned off as long as the backup batteries are installed or the AC plug

is connected.

● Enter an Original Voice Name

The PSR-2700 automatically creates a voice name for each sampled

voice. If you want to enter a more descriptive name for easier identification

(and this is recommended), this can be done via the keyboard after pressing

the DIGITAL SAMPLING section [VOICE NAME] button so that its indi-

cator lights. A voice name can consist of up to eight characters. Each key on

the keyboard enters a different character, listed immediately below the key.

The lowest key (C1) functions as a shift key that shifts between lower- and

upper-case characters: hold the SHIFT key while pressing a character key

to enter the upper-case character. Each time a character is entered the cursor

moves to the next character position. The F5 and F#5 keys move the cursor

backward and forward within the voice name. Use these keys to place the

cursor where you want to enter or change a character. The DELETE key

(G5) deletes the character at the cursor position. Press the ENTER key

(C6) when you’ve finished entering the voice name — this returns you to

the voice number display (your voice name will not be entered if you don’t

press the ENTER key).

NOTES

• Playing the keyboard will produce no sound during voice name entry.

• No name can be entered for a voice that contains no data.

SAMPLE PADS

1 2 3 4

VOICE #

VOICE

NAME

MNOPQRSTUVWXYZ012345678

08:Showtune 001:GrandPno

AccOff SVC=001:H–ello!

The recorded samples can be played simply by pressing the appropriate

SAMPLE PAD. The sample sounds only as long as the pad is held, so you

play only a section of a sample by releasing the pad early, or rapidly

retrigger the first section of the sample by repeatedly pressing the pad. The

pads can also be played at the same time so you can play all four samples

simultaneously, as required.

To select a different sample voice for playback via the pads, then press

the DIGITAL SAMPLING section [VOICE #] button and use the [+] and

[–] buttons, the number buttons, the data dial, or the [VOICE #] button

itself to select the desired sample voice number.

NOTES

• Different voices can be selected for playback via the pads and key-

board (see page 70), and these can be played simultaneously via the

pads and keyboard.

• To use sample pad data from disk, load the data into the PSR-2700

as described on page 60.

■Playing the Sample Pads

1 2 ... 64 65 66 67 68 69 70 71 72 73 74 ... 93 94

Comments to this Manuals

No comments

Yamaha PSR-2700 Owner's Manual Page 69

Comments to this Manuals

Related products and manuals for Musical Instruments Yamaha PSR-2700