Yamaha CVP-309GP Owner's Manual download pdf (Page 209)

CVP-309/307 Owner’s Manual

209

Appendix

CVP-309/307: Keyboard Stand Assembly

CAUTION

• Be careful not to confuse parts, and be sure to install all

parts in the correct direction. Please assemble in accor-

dance with the sequence given below.

• Assembly should be carried out by at least two persons.

• Be sure to use the correct screw size, as indicated below.

Use of incorrect screws can cause damage.

• Be sure to tighten up

all screws upon com-

pleting assembly of

each unit.

•To disassemble,

reverse the assembly

sequence given below.

Remove all parts from the box. Conﬁrm that all

parts shown in the illustration are provided.

With the key cover closed and the keyboard side

on the bottom, lean the unit against the wall.

CAUTION

• Be careful not to pinch your ﬁngers.

• The top part of the music rest is not ﬁxed. When you lean

the unit against the wall, support the music rest with your

hand so that the music rest will not fall.

CAUTION

• Do not place the main unit

with the rear side facing

down.

• Do not lay the main unit

upside-down on the ﬂoor.

Spread a large soft cloth such as a blanket on the

ﬂoor in front of the wall.

Place the main unit on the soft cloth with its

keyboard side facing the wall.

Place a protective pad on the soft cloth, so that,

when you place the main unit on the ﬂoor with its

keyboard side touching the ﬂoor, the pad comes

under the keyboard side, and is located about 10cm

(a little more than four inches) to the high key side

from the ﬂoppy disk drive. The pad will protect the

ﬂoppy disk drive so that it will not be damaged by

touching the ﬂoor.

Raise the rear of the main unit until it leans

against the wall. When raising the unit, place the

keyboard side at the bottom and make it sit on the

protective pad.

Be careful not to allow the unit to fall or slip.

Also, insert the soft cloth between the main unit

and the wall to protect the unit from being

damaged by hitting the wall or any other object.

CAUTION

Be sure to use a protective pad to avoid a damage to the

ﬂoppy disk drive. If the drive touches the ﬂoor when you

raise the unit to lean it against the wall, too much pressure

may be applied to the drive, possibly causing serious dam-

ages to the drive.

(CVP-307)

Spread a large soft cloth, such as a blanket, on the ﬂoor.

Place the unit on the cloth with the keyboard side on

the bottom and lean the unit against the wall so that the

unit will not fall or slip. Place a soft cloth against the

wall to protect the instrument and wall from scratches.

Attach the front legs.

Have a Phillips-head (+) screw-

driver ready.

Rear legFront leg (left)

AC power cord

Front leg (right)

Pedal box

5x18 mm ﬁxing

screws × 14

Bundled pedal

cord inside

CAUTION

To prevent the

key cover from

accidentally

opening during

assembly, press

down on the

key cover, mak-

ing sure that

the sheet

(shown) remain

in place.

Protective pad

(CVP-309)

Be sure to position the keyboard side on the bottom.

CAUTION

Please do not touch the speaker

net. Doing so may damage the

speaker inside.

Incorrect

Protective pad

Floppy disk drive

Large soft cloth

Floppy disk drive

Protective pad

(CVP-309)

Front leg (right) Front leg (left)

1 Fix the front right

leg to the bottom

surface of the unit

using two screws.

2 Fix the front right leg

to the speaker box

using two screws.

3 Fix the front left leg in the same way.

If the screw holes do not align, loosen the other screws and

adjust the position of the front leg.

4(CVP-309) Slowly tilt the main unit forward

until front legs reach the ﬂoor.

CVP-309_E.book Page 209 Monday, October 23, 2006 9:07 AM

1 2 ... 204 205 206 207 208 209 210 211 212 213 214 ... 223 224

Comments to this Manuals

No comments

Yamaha CVP-309GP Owner's Manual Page 209

Comments to this Manuals

Related products and manuals for Digital pianos Yamaha CVP-309GP