Yamaha RX-V2065 Manual download pdf (Page 66)

62 En

Controlling other components with the remote control

You can program remote control codes from other remote

controls. Use this feature if you want to program functions

not included in the basic operations covered by the remote

control codes, or an appropriate remote control code is not

available.

Note

<Note>

• Each of the steps described in this section should be performed within

one minute after the last step. If the next operation is not performed

within one minute, the programming operation is canceled. In this case,

start again from the beginning.

You can program the remote control to make functions of

an external component operable with the following keys.

You can assign functions to these keys for each input

source as with remote control codes.

cSOURCE POWER

kExternal component operation keys

lNumeric keys

• The remote control transmits infrared rays. If the remote control of the

external component also uses infrared rays, this remote control can learn

most of its functions. The remote control may not recognize special or

consecutive signals.

• The keys may not operate the assigned functions depending on operating

conditions of this unit.

1 Press oCODE SET on the remote control

using a pointed object such as the tip of a

ballpoint pen.

nTRANSMIT blinks twice.

2 Press the desired dInput selection key.

3 Press lNumeric keys to enter “9990”.

4 Press a key to which you want to assign the

function.

nTRANSMIT lights up and this unit enters a wait

state to receive remote control signals. Perform steps

5 and 6 within 10 seconds.

Note

<Note>

• If 10 seconds pass after this unit enters the wait state, a timeout

error occurs and nTRANSMIT turns off. In this case, repeat

from step 4.

5 Place the remote control about 5 to 10 cm

apart from the remote control of the external

component on a flat surface so that their

infrared transmitters are aimed at each other.

6 Press the key on the remote control of the

external component.

If the learning process is complete, nTRANSMIT

blinks twice. If it fails, nTRANSMIT blinks six

times. Repeat from step 4.

• Repeat steps 4 thorough 6 to assign a function to another key.

7 To end the operation, press oCODE SET

again.

nTRANSMIT blinks once.

1 Press oCODE SET on the remote control

using a pointed object such as the tip of a

ballpoint pen.

nTRANSMIT blinks twice.

2 Press the desired dInput selection key.

3 Press lNumeric keys to enter “9991”.

4 Press a key you want to reset.

If the key assignment is cleared, nTRANSMIT

blinks twice. If it fails, nTRANSMIT blinks six

times. Repeat from step 1.

• Repeat step 4 to clear another key assignment.

5 To end the operation, press oCODE SET

again.

nTRANSMIT blinks once.

1 Press oCODE SET on the remote control

using a pointed object such as the tip of a

ballpoint pen.

nTRANSMIT blinks twice.

2 Press the desired dInput selection key.

3 Press lNumeric keys to enter “9992”.

If the key assignments are cleared, nTRANSMIT

blinks twice. If it fails, nTRANSMIT blinks six

times. Repeat from step 1.

Programming from other remote

controls

Programming the remote control of this unit

DVD

RADIO

SLEEP

FM AM

INFO

MEMORY

1 2 3

5 6 1

PHONO

MULTI

DOCK

TUNER

V-AU X

HDMI

MUSIC

STEREO

ENHANCER SUR. DECODE

MOVIE

STRAIGHT

HDMI OUT

PURE DIRECT

USB/NET

PRESET TUNING

ON SCREEN OPTION

SOURCE

POWER

SCENE

RETURN

ENTER

VOLUME

DISPLAY

HDMI

AUDI O

TRANSMIT

CODE SET

MAIN

ZONE 2

ZONE 3

POWER

5 to 10 cm

Remote control of external component

Clearing the assignment of each key

Clearing the assignments of all keys

1 2 ... 61 62 63 64 65 66 67 68 69 70 71 ... 355 356

Comments to this Manuals

No comments

Yamaha RX-V2065 Manual Page 66

Comments to this Manuals

Related products and manuals for AV receivers Yamaha RX-V2065