Yamaha QX5 Manual download pdf (Page 13)

2. To stop play, press STOP/CONTINUE.

3. To restart play, press START to play from the beginning of the Pattern, or STOP/

CONTINUE to play from the point at which play was stopped.

During Pattern play, you can change the Tempo using the TEMPO slider, or using

operation 1.7.1.

2.1.2 LOADING THE PRESET PATTERNS

NOTE: This operation also loads the RX17’s preset Songs into Song locations 0–3.

The preset Patterns in Pattern locations 50–99 are there to be played, edited, copied

or cleared as you wish. However, they are permanently stored in the RX17, and can be

re-loaded into the Pattern locations at any time.

BEFORE turning the RX17’s power on, hold down the +1 YES key and the STOP/

CONTINUE key. Keep holding these keys while turning the power on.

The preset Patterns will now be loaded into Pattern locations 50–99.

NOTE: All previous data in Patterns 50-99 will be erased. If this data is important,

save it to tape (operation 4.1) BEFORE executing the Load Preset Patterns operation.

2.1.3 USING THE PATTERN CHART

Near the end of this manual you will find a Pattern Chart. You can copy this chart and

use the copies to keep an absolutely accurate written record of Patterns that you have

created on your RX17. This chart accommodates the data of a 4/4 Pattern written at the

maximum Quantize setting of 1/48. Longer Patterns may be recorded by using two

Pattern Charts. Enter data as follows:

Enter Note Markers (solid dots) at the intersections of the lines.

Indicate accented notes using a circle.

If you have used the Accent Edit function to alter the Accent Level of any notes, write

the new Accent Level next to the Note Markers for those notes.

Enter the Level, Accent Level and Quantize setting of each instrument.

Enter the Pan setting of each instrument, using a number from 1 – 15. 1 means Left;

15 means Right; 8 means Center. Other positions are numbered corresponding to

the mark at which the cursor is set on the LCD Pan display.

2.2 REAL TIME WRITE

This is the first of two ways of writing Patterns on the RX17. It lets you “play” a Pattern

on the instrument keys, while listening to a click guide. You can add instruments and

rhythms until the Pattern is complete. The advantage of this method is that you can

actually hear the Pattern being built up as you write it, as opposed to Step Write, where

a Pattern is built up without hearing it.

NOTE: You can also execute Real Time writing of Patterns using an external MIDI

keyboard to “play” the RX17’s instruments. This is highly convenient because all 26

RX17 instruments can be assigned to a keyboard (compared to using the RX17’s

instrument keys, with a maximum of 13 instruments available at anyone time). Another

advantage is that the RX17 will accept MIDI Key Velocity data, so that the harder you

play a key on your MIDI synthesizer, the louder the RX17’s note will be. See 6.5.3 MIDI

NOTE RECEIVE for an explanation of the settings required for this MIDI application.

2.2.1 ENTERING REAL TIME WRITE

1. After selecting a Pattern, select Function 2.

Press

+1 YES

to enter Real Time Write. The LCD will show the Pattern LENGTH display.

NOTE: If you decide you do NOT want to enter Real Time Write, press PATTERN to

return to Select Pattern.

2.2.2 SETTING PATTERN LENGTH

Providing you have selected an empty Pattern, you can now set the time signature

(length) of your Pattern. Pattern Lengths are displayed in 16th notes. For example, 16/16

(the default Pattern Length displayed when you call an empty Pattern) is equivalent to

a bar of 4/4 time (4 quarter-notes per bar); 12/16 indicates a bar of 3/4 time, and so on.

Use the –1 NO and +1 YES keys to set the time signature. RANGE: 1/16–32/16.

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 46 47

Comments to this Manuals

No comments

Yamaha QX5 Manual Page 13

Comments to this Manuals

Related products and manuals for Sequencer Yamaha QX5