Yamaha DTX700 Owner's Manual download pdf (Page 55)

DTX700 Owner’s Manual

On-Screen Messages

Message Full meaning

Are you sure? This message is displayed to confirm whether or not you wish to proceed with the selected operation.

Completed. This message is displayed when loading, saving, formatting, and other similar operations have been completed.

Connecting USB device... This message is displayed when your DTX700 is busy mounting a USB memory device.

Copy protected.

This message is displayed if operations such as wave editing cannot be performed due to the digital audio source

being copy protected.

Excessive demand for USB power.

This message is displayed if the current being drawn by the USB memory device exceeds the level supported by your

DTX700.

Executing...

This message is displayed while your DTX700 is busy performing formatting or another similar management task.

Please wait until the operation is completed.

File already exists. This message is displayed if a file with the same name as the one you are about to save already exists.

File not found. This message is displayed if no file of the selected type exists.

Illegal file.

This message is displayed if the file selected for loading is unsuitable for use with your DT

X700 or is unsuitable for the

current mode.

Illegal file name. This message is displayed if the specified file name is not valid.

Illegal format.

This message is displayed if the standard MIDI file (SMF) you are attempting to import is of Format 1. Please select an

SMF of Format 0 to proceed.

Illegal selection. This message is displayed if an operation cannot be performed in accordance with the settings made.

Illegal wave data. This message is displayed if the audio file you are attempting to import is of an unsupported format.

Incompatible USB device. This message is displayed if an unsupported USB device is plugged into the instrument’s [USB TO DEVICE] port.

Invalid USB device.

This message is displayed if the plugged-in USB memory device is not usable in its current condition. As long as the

device contains no irreplaceable data, it should be formatted to make it usable.

MIDI buffer full. This message is displayed if the volume of MIDI data received is too large to process.

MIDI data error. This message is displayed if an error occurs while receiving MIDI data.

No data.

This message is displayed if you are attempting to perform a song management task even though the selected song

contains no data, or if you attempt to play recorded data when none exists.

No response from USB device. This message is displayed if the plugged-in USB memory device fails to respond.

No unused MIDI note. This message is displayed upon execution of a copy-pad operation if no unused

MIDI notes are available.

No wave data. This message is displayed if you are attempting to perform a wave management task even though no wave data exists.

Now importing...[EXIT] to cancel. This message is displayed while your DTX700 is busy importing wave data.

Now loading...[EXIT] to cancel. This message is displayed while your DTX700 is busy loading a file.

Now saving... [EXIT] to cancel. This message is displayed while your DTX700 is busy saving a file.

Now working...

This message is displayed while your DTX700 is tidying up after importing a wave or after you press the [EXIT] button

to cancel a load or save operation.

Overwrite?

This message is displayed when saving files to confirm whether or not you wish to overwrite a file of the same name

already present on the USB memory device.

Please keep power on.

This message is displayed while your DTX700 is writing data to its flash ROM. You should never turn off the instrument

while it is in this state. If this precautio

n is not observed, user data may be lost or the internal system may be damaged,

rendering your DTX700 unable to startup normally when it is next turned on.

Please stop sequencer.

This message is displayed to remind you to stop the sequencer (i.e., song playback) before performing the intended

operation.

Read only file. This message is displayed if you are attempting to perform a file operation using a read-only file.

Sample is protected. This message is displayed if the selected audio file is write protected and cannot be overwritten.

Sample is too long. This message is displayed if the audio file is too long to be loaded.

Sample is too short. This message is displayed if the audio file is too short to be loaded.

Seq memory full.

This message is displayed if the instrument’s internal memory for sequence data is full, making it impossible to record

new songs, perform associated management tasks, or load data from a USB memory device. To free up some of this

sequence memory, delete unneeded User patterns.

Stored. This message is displayed to confirm that data has been successfully stored.

System memory crashed. This message is displayed if a problem occurred while writing data to the instrument’s internal flash ROM.

USB connection terminated.

This message is displayed if connection wit

h the USB memory device was interrupted by an abnormal electric current.

Unplug the USB memory device and press the dial to return.

USB device full.

This message is displayed if the USB-memory device is full and no more files can be saved on it. In such a case, use

a new USB memory device or make space by erasing unwanted data from the current device.

USB device not ready. This message is displayed if the USB memory device has not been correctly plugged into your DTX700.

USB device read/write error. This message is displayed if an error occurred during the exchange of data with the USB memory device.

USB device write protected.

This message is displayed if the USB memory device is write protected or if you are attempting to save data on a read-

only device such as a CD drive.

USB host not ready.

This message is displayed if the Cubase Remote function is turned on without first connecting the DTX700 to a com-

puter.

USB transmission error. This message is displayed if an error occurred during communication with the USB memory device.

Wave memory full.

This message is displayed if your DTX700’s wave memory is full, preventing operations such as the importing and

loading of data.

dtx700_en_om.book Page 55 Friday, December 17, 2010 4:34 PM

1 2 ... 50 51 52 53 54 55 56 57 58 59 60 ... 63 64

Comments to this Manuals

No comments

Yamaha DTX700 Owner's Manual Page 55

Comments to this Manuals

Related products and manuals for Music drums Yamaha DTX700