Yamaha HTR-5560 Service Manual Page 9
- Page / 114
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
RX-V730/RX-V730RDS/RX-V630/RX-V630RDS
HTR-5560/HTR-5560RDS/DSP-AX630/DSP-AX630SE
21
RX-V730/RX-V730RDS/RX-V630/RX-V630RDS
HTR-5560/HTR-5560RDS/DSP-AX630/DSP-AX630SE
Opening message /
オープニング表示
DIAG menu display /
ダイアグメニュー表示
After a few seconds
Version (1 alphabet)
When there is no history
of protection function
When there is a history of protection function:
When there is a history of protection
function due to excess current
Version (1 alphabet)
プロテクション履歴がある場合:
CAUTION!
Using this product with the protection function disabled
may cause damage to itself. Use special care for this point
when using this mode.
• Canceling DIAG
[1] Before canceling DIAG, execute setting for PRESET of
DIAG menu No.9 (Memory initialization inhibited or
Memory initialized).
* In order to keep the user memory stored, be sure to
select PRESET INHIBITED (Memory initialization
inhibited). Protection history will remain memory.
[2] Turn off the power by pressing the “STANDBY/ON”
key of the main unit.
• Display provided when DIAG started
RX-V730/RX-V730RDS: When the monitor is connected,
DIAGNOSTIC MENU appears on its screen as shown in
the figure. (It remains on display until DIAG is cancelled.)
注意！
プロテクションを解除した状態でのダイアグモードは、
危険な状態でもプロテクションが作動しないため、動作
させると、機器を破壊することがあります。このモード
を使用する場合は十分注意してください。
● ダイアグの解除
● ダイアグ起動時の表示
プロテクション履歴がない場合:
The FL display of the main unit displays the protection
function history data and the version (1 alphabet) and the
DIAG menu [sub-menu (ANALOG BYPASS) of DIAG
menu No.1 DSP THROUGH] a few seconds later.
When there is no history of protection function:
- AV RECEIVER/AV AMPLIFIER 1
- ■ INTERNAL VIEW 2
- パワートランジスタ、スピーカー保護リレーの交換 6
- Protection Relay 6
- • Starting DIAG 8
- ● ダイアグの起動 8
- ● プロテクション解除モードでの起動 8
- • Canceling DIAG 9
- ● ダイアグの解除 9
- ● ダイアグ起動時の表示 9
- ● メニュー動作中の表示 11
- SUB-MENU 12
- ● ダイアグメニューとサブメニューの操作 12
- • Functions in DIAG mode 13
- ● ダイアグ中の機能 13
- ● ダイアグ開始時の初期設定 13
- • Details of DIAG menu 14
- ● ダイアグメニュー詳細 14
- L/(L+R)/2 15
- 2. RAM THROUGH 16
- 3. PRO LOGIC 17
- 4. SPEAKERS SET 18
- 5. MARGIN CHECK 19
- 6. OTHER INPUT 20
- 7. DISPLAY CHECK 20
- ■ AMP ADJUSTMENT / アンプ部調整 28
- ■ DISPLAY DATA 29
- ■ IC DATA 31
- 16bit µ-COM (Main CPU) 32
- IC600 : YSS938 33
- O: Digital output terminal 36
- A: Analog terminal 36
- ■ PIN CONNECTION DIAGRAM 37
- ■ BLOCK DIAGRAM (1/2) 38
- ■ BLOCK DIAGRAM (2/2) 39
- : except 40
- DSP-AX630SE 40
- RX-V730RDS: not used 40
- DSP-AX630SE: 33K 40
- SCHEMATIC DIAGRAM (MAIN 1/2) 43
- SCHEMATIC DIAGRAM (MAIN 2/2) 44
- REGULATOR 44
- SCHEMATIC DIAGRAM (POWER) 45
- SCHEMATIC DIAGRAM (OPERATION) 46
- SCHEMATIC DIAGRAM (DSP) 47
- DSP P. C. B 48
- (Lead Type Device) 48
- (Surface Mount Device) 49
- FUNCTION (1) P. C. B 50
- FUNCTION (2) P. C. B 52
- : except DSP-AX630SE 53
- : RX-V730/ 53
- RX-V730RDS only 53
- FUNCTION (4) 54
- FUNCTION 54
- MAIN (1) P. C. B 56
- IMPEDANCE SELECTOR 57
- (except J model) 57
- R371, 372, 375 X X O O 58
- X: NOT USED 58
- O: USED / APPLICABLE 58
- SW711~714 X O 59
- R711~714 X O 60
- Power Transformer 61
- MAIN (2) 61
- AC Power Cord 61
- MAIN (4) 62
- MAIN (1) 62
- ■ TO SERVICE PERSONNEL 63
- ■ IMPEDANCE SELECTOR 63
- ■ FRONT PANELS 64
- ■ REAR PANELS 66
- DSP-AX630SE (G model) 71
- DSP-AX630SE (B model) 71
- ■ REMOTE CONTROL 72
- ■ SPECIFICATIONS / 参考仕様 73
- • Set Menu Table / セットメニュー 74
- PARTS LIST 75
- P.C.B. FUNCTION 76
- P.C.B. OPERATION 84
- P.C.B. DSP 86
- P.C.B. DSP & P.C.B. MAIN 90
- P.C.B. MAIN 91
- P.C.B. POWER 100
- Chip Resistors 101
- ■ EXPLODED VIEW 102
- ■ MECHANICAL PARTS 103
- RX-V730/RX-V730RDS 104
- ● SCHEMATIC DIAGRAM 110
- EX/ESEX/ES 113
- 1/4W Type 114
- 1/6W Type 114
© 2020, manymanuals.com. All rights reserved. | 1.432 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals