Yamaha HTR-5560 Service Manual Page 8
- Page / 114
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
RX-V730/RX-V730RDS/RX-V630/RX-V630RDS
HTR-5560/HTR-5560RDS/DSP-AX630/DSP-AX630SE
RX-V730/RX-V730RDS/RX-V630/RX-V630RDS
HTR-5560/HTR-5560RDS/DSP-AX630/DSP-AX630SE
20
No DIAG menu sub-menu
11. BSI (YSS) 3 (5 Byte)
12. BSI (YSS) 4 (4 Byte)
13. BSI (CS) 1 (5 Byte)
14. BSI (CS) 2 (5 Byte)
15. BSI (CS) 3 (5 Byte)
16. BSI (CS) 4 (5 Byte)
17. BSI (CS) 5 (1 Byte)
18. YSS938-1 (5 Byte)
19. YSS938-2 (5 Byte)
20. YSS938-3 (4 Byte)
21. CS49329 (3 Byte)
22. Mute Trigger (5 Byte)
12 DSP RAM CHECK 1. YSS938 BUS CHECK
2. PLD/CS BUS CHECK
13 SOFT SWITCH 1. SW MODE
2. MODEL SETTING
3. TUNER DESTINATION
4. TUNER EXIST
6. RDS EXIST
7. VIDEO FORMAT
14 ROM VERSION/CHECK SUM/ 1. VERSION
PORT 2. CHECK SUM ALL/PROGRAM
3. PORT
4. AAC PORT
• Starting DIAG
Press the “STANDBY/ON” key while simultaneously
pressing those two keys of the main unit as indicated in the
figure below.
● ダイアグの起動
DSP-AX630SE
Turn on the power while pressing these keys.
Keys of main unit
except DSP-AX630SEDSP-AX630SE
Turn on the power while pressing these keys.
• Starting DIAG in the protection cancel
mode
If the protection function works and causes hindrance to
trouble diagnosis, cancel the protection function as
described below, and it will be possible to enter the DIAG
mode. (The protection functions other than the excess
current detect function will be disabled.)
Press the “STANDBY/ON” key while simultaneously
pressing those two keys indicated in the figure above. At
this time, keep pressing those two keys for 3 seconds or
longer.
In this mode, the “SLEEP” segment of the FL display of the
main unit flashes to indicate that the mode is DIAG mode
with the protection functions disabled.
● プロテクション解除モードでの起動
- AV RECEIVER/AV AMPLIFIER 1
- ■ INTERNAL VIEW 2
- パワートランジスタ、スピーカー保護リレーの交換 6
- Protection Relay 6
- • Starting DIAG 8
- ● ダイアグの起動 8
- ● プロテクション解除モードでの起動 8
- • Canceling DIAG 9
- ● ダイアグの解除 9
- ● ダイアグ起動時の表示 9
- ● メニュー動作中の表示 11
- SUB-MENU 12
- ● ダイアグメニューとサブメニューの操作 12
- • Functions in DIAG mode 13
- ● ダイアグ中の機能 13
- ● ダイアグ開始時の初期設定 13
- • Details of DIAG menu 14
- ● ダイアグメニュー詳細 14
- L/(L+R)/2 15
- 2. RAM THROUGH 16
- 3. PRO LOGIC 17
- 4. SPEAKERS SET 18
- 5. MARGIN CHECK 19
- 6. OTHER INPUT 20
- 7. DISPLAY CHECK 20
- ■ AMP ADJUSTMENT / アンプ部調整 28
- ■ DISPLAY DATA 29
- ■ IC DATA 31
- 16bit µ-COM (Main CPU) 32
- IC600 : YSS938 33
- O: Digital output terminal 36
- A: Analog terminal 36
- ■ PIN CONNECTION DIAGRAM 37
- ■ BLOCK DIAGRAM (1/2) 38
- ■ BLOCK DIAGRAM (2/2) 39
- : except 40
- DSP-AX630SE 40
- RX-V730RDS: not used 40
- DSP-AX630SE: 33K 40
- SCHEMATIC DIAGRAM (MAIN 1/2) 43
- SCHEMATIC DIAGRAM (MAIN 2/2) 44
- REGULATOR 44
- SCHEMATIC DIAGRAM (POWER) 45
- SCHEMATIC DIAGRAM (OPERATION) 46
- SCHEMATIC DIAGRAM (DSP) 47
- DSP P. C. B 48
- (Lead Type Device) 48
- (Surface Mount Device) 49
- FUNCTION (1) P. C. B 50
- FUNCTION (2) P. C. B 52
- : except DSP-AX630SE 53
- : RX-V730/ 53
- RX-V730RDS only 53
- FUNCTION (4) 54
- FUNCTION 54
- MAIN (1) P. C. B 56
- IMPEDANCE SELECTOR 57
- (except J model) 57
- R371, 372, 375 X X O O 58
- X: NOT USED 58
- O: USED / APPLICABLE 58
- SW711~714 X O 59
- R711~714 X O 60
- Power Transformer 61
- MAIN (2) 61
- AC Power Cord 61
- MAIN (4) 62
- MAIN (1) 62
- ■ TO SERVICE PERSONNEL 63
- ■ IMPEDANCE SELECTOR 63
- ■ FRONT PANELS 64
- ■ REAR PANELS 66
- DSP-AX630SE (G model) 71
- DSP-AX630SE (B model) 71
- ■ REMOTE CONTROL 72
- ■ SPECIFICATIONS / 参考仕様 73
- • Set Menu Table / セットメニュー 74
- PARTS LIST 75
- P.C.B. FUNCTION 76
- P.C.B. OPERATION 84
- P.C.B. DSP 86
- P.C.B. DSP & P.C.B. MAIN 90
- P.C.B. MAIN 91
- P.C.B. POWER 100
- Chip Resistors 101
- ■ EXPLODED VIEW 102
- ■ MECHANICAL PARTS 103
- RX-V730/RX-V730RDS 104
- ● SCHEMATIC DIAGRAM 110
- EX/ESEX/ES 113
- 1/4W Type 114
- 1/6W Type 114
© 2020, manymanuals.com. All rights reserved. | 1.441 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals