Yamaha RX-V1300 Manual Page 15
- Page / 88
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
11
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
SPEAKER SETUP
12
Connecting the Speakers
Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are
faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound
will be unnatural and lack bass.
CAUTION
• Use speakers with the specified impedance shown on the rear panel of this unit.
• Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could
damage this unit and/or speakers.
If necessary, use the SET MENU to change the speaker mode settings according to the number and size of the speakers
in your configuration after you finish connecting your speakers.
■ Speaker cables
A speaker cable is actually a pair of insulated cables
running side by side. One of the cables is colored or
shaped differently, perhaps with a stripe, groove or ridge.
1 Remove approximately 10 mm (3/8”) of
insulation from each of the speaker cables.
2 Twist the exposed wires of the cable
together to prevent short circuits.
■ Connecting to the SPEAKERS terminals
1 Unscrew the knob.
2 Insert one bare wire into the hole in the side
of each terminal.
3 Tighten the knob to secure the wire.
y
(For U.S.A., Canada, Australia, China and General models)
• Banana plug connections are also possible. First, tighten the
knob and then insert the banana plug connector into the end of
the corresponding terminal.
10 mm (3/8”)
■ MAIN SPEAKERS terminals
One or two speaker systems can be connected to these terminals. If you use only one speaker system, connect it to either
of the MAIN A or B terminals.
■ REAR SPEAKERS terminals
A rear speaker system can be connected to these terminals.
■ CENTER SPEAKER terminals
A center speaker can be connected to these terminals.
■ REAR CENTER SPEAKER terminals
A rear center speaker can be connected to these terminals.
Red: positive (+)
Black: negative (–)
Banana plug
3
1
2
0103V1300_10-20_EN(U) 02.8.5, 5:39 PM11
- RX-V1300 1
- IMPORTANT SAFETY INSTRUCTIONS 2
- CAUTION II 3
- III CAUTION 4
- CONTENTS 5
- FEATURES 6
- GETTING STARTED 7
- CONTROLS AND FUNCTIONS 8
- Remote Control 10
- Using the Remote Control 11
- Front Panel Display 12
- Rear Panel 13
- SPEAKER SETUP 14
- Connecting the Speakers 15
- COMPONENT VIDEO 16
- SELECTOR 17
- (U.S.A. and Canada models) 17
- IMPEDANCE 17
- CONNECTIONS 18
- Connecting Audio Components 21
- Connecting the Antennas 23
- Connecting to the 6CH INPUT 24
- Connecting to an External 24
- Amplifier 24
- To AC outlet 25
- Turning on the Power 26
- ON-SCREEN DISPLAY (OSD) 27
- SPEAKER MODE SETTINGS 28
- Before You Begin 29
- 4 Adjust the output level of 30
- 5 When the adjustment is 30
- BASIC PLAYBACK 31
- Input Modes and Indications 33
- 1 Press AMP to select the 34
- or Neo: 6 35
- Matrix 6.1 ~ 36
- Front panel 37
- Remote control 37
- Understanding Sound Fields 38
- Hi-Fi DSP Programs 38
- CINEMA-DSP 38
- Sound Field Effect 39
- Straight Decode 39
- Features of DSP Programs 40
- Automatic and Manual Tuning 43
- A1:FM~~~~~~~~~ 44
- A~ AM~~630~kHz 45
- Exchanging Preset Stations 46
- Tuning in to a Preset Station 46
- BASIC RECORDING 47
- REMOTE CONTROL FEATURES 48
- Setting the Manufacturer Code 49
- Learn Feature 51
- Display Window 52
- Clearing Learned Functions 53
- Renamed Source Names, and 53
- Setup Manufacturer Codes 53
- Each Component Control Area 54
- SET MENU 59
- 1 SPEAKER SET (speaker mode 60
- 1C REAR L/R SP 61
- 1D REAR CT SP 62
- 2 LOW FRQ TEST 63
- 5 CENTER GEQ 64
- 4 HP TONE CTRL 64
- 6 INPUT RENAME 65
- 7 I/O ASSIGNMENT 65
- 8 INPUT MODE (initial input 66
- 11 D-RANGE (dynamic range) 67
- 9 PARAM. INI (parameter 67
- 10 LFE LEVEL 67
- 12 SP DELAY 68
- 13 DISPLAY SET 69
- 14 MEMORY GUARD 69
- 15 6CH INPUT SET 69
- SLEEP TIMER 71
- REMOTE CONTROL OUT 72
- CD INPUT 72
- REMOTE CONTROL IN 72
- ZONE 2 AUDIO OUT 72
- Remote Control in Zone 2 73
- What is a Sound Field? 74
- Resetting a Parameter to the 75
- Factory-set Value 75
- Changing Parameter Settings 75
- 60 dB 60 dB 60 dB 78
- TROUBLESHOOTING 80
- GLOSSARY 85
- SPECIFICATIONS 87
Related products and manuals for AV receivers Yamaha RX-V1300
AV receivers Yamaha RX-A760 Owner's Manual
(154 pages)
(154 pages)
AV receivers Yamaha RX-V365 User Manual
(2 pages)
(2 pages)
AV receivers Yamaha RX-V3071 Setup Guide
(8 pages)
(8 pages)
AV receivers Yamaha RX-V465 Owner's Manual
(74 pages)
(74 pages)
AV receivers Yamaha RX-V1800 Owner's Manual
(151 pages)
(151 pages)
AV receivers Yamaha RX-V630 Owner's Manual
(67 pages)
(67 pages)
AV receivers Yamaha RX-V365 Owner's Manual
(62 pages)
(62 pages)
AV receivers Yamaha YHT-S401 Manual
(70 pages)
(70 pages)
AV receivers Yamaha RX-V767 Manual
(133 pages)
(133 pages)
AV receivers Yamaha RX-V800 Owner's Manual
(82 pages)
(82 pages)
AV receivers Yamaha HTR-5065 Owner's Manual
(108 pages)
(108 pages)
AV receivers Yamaha HTR-5064 Setup Guide
(8 pages)
(8 pages)
AV receivers Yamaha CRX-330 Owner's Manual
(40 pages)
(40 pages)
AV receivers Yamaha RX-V863 Owner's Manual
(538 pages)
(538 pages)
AV receivers Yamaha HTR-4063 Manual
(97 pages)
(97 pages)
AV receivers Yamaha RX-A670 Owner's Manual
(140 pages)
(140 pages)
AV receivers Yamaha TSR-6750 Setup Guide
(58 pages)
(58 pages)
© 2020, manymanuals.com. All rights reserved. | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals