Yamaha RX-V1067 Quick Start Guide Page 3

  • Download
  • Add to my manuals
  • Print
  • Page
    / 8
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 2
AC
SURROUND SURROUND BACK/
SPEAKERS
CENTER
AV 1 AV 2 AV 3 AV 4
HDMI
AV 5 AV 6 AV 7
SINGLE
FRONT
BI-AMP
AV 3
AV 4
F
RONT
SURROUND
SUR. BACK
SUBWOOFER
CENTER
MULTI CH INPUT
COMPONENT VIDEO
MONITOR OUT/ZONE OUT
ZONE OUT PRE OUT
ZONE 2
YP
B
P
R
P
B
P
R
YP
B
P
R
C
D
SURROUND
SUR. BACK
CENTER
SUBWOOFER
1
2
RS-232C
2
1
TRIGGER
OUT
+12V 0.1A MAX.
FRONT
(1 BD/DVD)
(SINGLE)
ZONE2/
F.PRESENCE
EXTRA SP
IN
OUT
REMOTE
A
C
S
P
E
K
E
R
S
A
V
A
A
1
A
V
A
A
2
A
V
A
A
3
A
V
A
A
4
H
D
M
I
A
V
A
A
5
A
V
A
A
6
A
V
A
A
7
A
V
A
A
3
A
V
A
A
4
F
R
O
N
T
S
U
R
R
O
U
N
D
S
U
R
.
B
A
C
K
S
U
B
W
O
O
F
E
R
C
E
N
T
E
R
M
U
L
T
L
L
I
C
H
I
N
P
U
T
C
O
M
P
O
N
E
N
T
V
I
D
E
O
M
O
N
I
T
O
R
O
U
T
/
T
T
Z
/
/
O
N
E
O
U
T
Z
O
N
E
O
U
T
P
R
E
O
U
T
Z
O
N
E
2
Y
P
B
P
R
P
B
P
R
Y
P
B
P
R
C
D
S
U
R
R
O
U
N
D
S
U
R
.
B
A
C
K
C
E
N
T
E
R
S
U
B
W
O
O
F
E
R
2
R
S
-
2
3
2
C
2
1
T
R
I
G
G
E
R
O
U
T
+
1
2
V
0
.
1
A
M
A
X
.
F
R
O
N
T
(
1
B
D
/
D
V
D
)
(
S
I
N
G
L
E
)
Z
O
N
E
2
/
F
.
F
F
P
R
E
S
E
N
C
E
E
X
T
R
A
S
P
I
N
O
U
T
R
E
M
O
T
E
6.1
7.1 7.1
- 3 -
1
1
Connect the speakers
Front speaker
R L
Subwoofer
Center speaker
R L
Surround back
speaker
R L
Surround
speaker
Connecting speakers
Connecting the subwoofer
1
Connect the subwoofer input jack to the
SUBWOOFER 1 jack on this unit with an audio
pin cable.
(
S
I
N
GL
E
)
S
U
B
WOO
FE
R
PRE OUT
CE
N
T
E
R
CE
N
T
E
R
S
U
R.
BA
CK
S
U
R
R
U
N
D
1
2
FRONT
When connecting the presence speakers, refer to “Presence speaker
connection” in the Owner’s Manual.
This unit can connect speakers that support Bi-amp connection for front
speakers. Refer to “Bi-amp connection” in the Owner’s Manual.
7.1
Connect when using with 7.1-channel speaker layout.
6.1
Connect when using with 6.1-channel speaker layout.
2
Set the subwoofer volume as follows.
Volume: Set to approximately half volume (or slightly less than half).
Crossover frequency (if available): Set to maximum.
Subwoofer examples
VOLUME
MIN MAX
CROSSOVER/
HIGH CUT
MIN MAX
Caution:
Remove the power cable of this unit from the power outlet before
connecting the speakers.
Generally speaker cables consist of two parallel insulated
cables. One of these cables is a different color, or has a line
running along it, to indicate different polarity. Insert the different
colored (or lined) cable into the “+” (positive, red) terminal
on this unit and the speakers, and the other cable into the “-”
(minus, black) terminal.
Be careful that the core of the speaker cable does not touch
anything or come into contact with the metal areas of this unit.
This may damage this unit or the speakers. If the speaker cables
short circuit, “CHECK SP WIRES!” will appear on the front panel
display when this unit is switched on.
This unit is con gured for 8Ω speakers at the factory setting.
When connecting 6Ω speakers, con gure the speaker impedance
setting of this unit to 6Ω. When this unit is con gured for 6Ω
speakers, 4Ω speakers can also be used as the front speakers.
For more information on setting the speaker impedance, refer to
“Changing speaker impedance” in the Owner’s Manual.
FRO
NT
-
2
2
3
1
4
4
+
1
Remove approximately 10 mm of insulation from
the ends of the speaker cables, and twist the bare
wires of the cables together  rmly so that they will
not cause short circuits.
2
Loosen the speaker terminals.
3
Insert the bare wire of the speaker cable into the
gap on the side of the terminal.
4
Tighten the terminal.
Page view 2
1 2 3 4 5 6 7 8

Comments to this Manuals

No comments