PREPARATIONS ➤ Optimizing the speaker settings automatically (YPAO) En 33
• To cancel the operation, disconnect the YPAO microphone, or use the
cursor keys to select “Exit” and press ENTER, before starting the
measurement.
• To change the internal amplifier assignment, use "Power Amp Assign" (p.81)
in the "Setup" menu.
• Do not stand between the speakers and the YPAO microphone during the
measurement process (about 3 minutes).
• Move to the corner of the room or leave the room.
5
To start the measurement, use the cursor keys to
select “Start” and press SETUP.
The measurement will start in 10 seconds. Press ENTER to
start the measurement immediately.
• To stop the measurement temporarily, press RETURN and follow the
procedure in “Error messages” (p.34).
• If cursor keys do not work, the remote control may be set to the external
device operation mode. In this case, press RECEIVER to set the remote
control to the unit operation mode and then use the cursor keys.
The following screen appears on the TV when the
measurement finishes.
1 The number of speakers (front side/rear
side/subwoofer)
2 Speaker distance (nearest/farthest)
3 Adjustment range of speaker output level
4 Warning message (if available)
• If any error message (such as E-1) or warning message (such as W-1)
appears, see “Error messages” (p.34) or “Warning messages” (p.35).
• A speaker with a problem is indicated by blinking of the speaker indicators in
the front display.
• If multiple warnings are given (when operating with the front display), use
the cursor keys (q/w) to check the other warning messages.
6
To save the measurement results, use the cursor
keys (e/r) to select “SAVE” and press ENTER.
The adjusted speaker settings are applied.
• To finish the measurement without saving the result, select “CANCEL”.
7
Disconnect the YPAO microphone from the unit.
This completes optimization of the speaker settings.
1
2
3
4
Auto Setup
Start
Exit
Measurement
Finished
Result
3 / 2 / 0.1 ch
3.0 / 10.5 m
-3.0 / +10.0 dB
OK:ENTER
Caution
• The YPAO microphone is sensitive to heat, so should not be placed anywhere
where it could be exposed to direct sunlight or high temperatures (such as on
top of AV equipment).
Auto Setup
Start
Exit
Measurement
Finished
Result
3 / 2 / 0.1 ch
3.0 / 10.5 m
-3.0 / +10.0 dB
SAVE
1 2 3 4 5 6 7 8 9 10
TV VOL TV CH
TV
INPUT
MUTE
CODE SET
90
10
ENT
5
687
1234
MOVIE
ENHANCER
TUNING PRESET
MEMORY
DISPLAYRETURN
ENTER
SETUP OPTION
TOP MENU
MUTE
PROGRAM VOLUME
POP-UP/MENU
DIRECT
STRAIGHT
INFO SLEEP
MUSIC
FM
PARTY
MAIN
ZONE 2
NET
MODE
SCENE
BD
DVD
TV
NET
RADIO
SOURCE
RECEIVER
HDMI
AV
AUDIO
5
4
1234
12
52
31
SUR. DECODE
V-AUX
USB
AM
V
H
INP
MUTE
DE
E
9
1 2
4
VIE
NHANCE
T
NIN
P
E
ET
MEM
RY
DI
PLA
TI
OP MENU
U
E
R
RA
V
L
M
P
P-UP
MEN
DIREC
TRAI
INF
LEE
I
PART
Z
NE
M
DE
EN
UR
E
DI
2
R. DE
D
-
B
SETUP
ENTER
RETURN
RECEIVER
Cursor keys
RX-S600_S600D_om.book Page 33 Tuesday, May 28, 2013 1:36 PM
Comments to this Manuals