Yamaha RX-V571 Owner's Manual download pdf (Page 32)

En 32

Error messages

If any error message is displayed during the measurement, resolve the problem and perform YPAO again. Error message can be confirmed and controlled by viewing both a TV

monitor and the front display.

■ Procedure to exit YPAO

1 Check the contents of error message, and then press ENTER.

2 Press the cursor key ( ) to select “EXIT (Exit)” from the following

choices, and then press ENTER.

Choices: PROCEED (Proceed) (E-5, E-9 only), “RETRY (Retry),” “EXIT (Exit)”

3 Press the cursor key ( ) to select “Exit (Exit)” from the following

choices, and then press ENTER.

Choices: Start (Start), Exit (Exit)

4 Remove the YPAO microphone.

■ Cause and remedy for each error message

TV monitor Front display

STEREO

SLEEP

VOL.

TUNED

PL PR

SL SR

ENHANCER

iPod

CHARGE

SL SR

E-1:NO FRNT SP

YPAO

VOL.

Error message Cause Remedy

E-1:No Front SP

(E-1:NO FRNT SP)

Front speakers are not

detected.

Follow “Procedure to exit YPAO” to exit YPAO, turn off the unit, and then check the speaker connections. After removing problems, turn on the unit, and

then perform YPAO again.

E-2:No Sur. SP

(E-2:NO SUR SP)

Either of surround

speakers is not detected.

E-4:SBR→SBL

(E-4:SBR->SBL)

A surround back speaker

is connected to the R side

only.

When using only one surround back speaker, you need to connect it to the SINGLE jack (L side). Follow “Procedure to exit YPAO” to exit YPAO, turn off the

unit, and then reconnect the speaker. After reconnecting, turn on the unit, and then perform YPAO again.

E-5:Noisy

(E-5:NOISY)

The noise is too loud.

Keep the room quiet and select “RETRY (Retry)” in step 2 of “Procedure to exit YPAO” to restart YPAO for an accurate measurement. Selecting

“PROCEED (Proceed)” allows you to continue measuring, but may not achieve the optimal results.

We recommend selecting “RETRY (Retry)” or “EXIT (Exit)” to retry YPAO again from the beginning.

E-6:Check Sur.

(E-6:CHECK SUR)

Any surround back

speaker is connected

while no surround

speakers are connected.

Surround speakers should be connected when using surround back speakers. Follow “Procedure to exit YPAO” to exit YPAO, turn off the unit, and then

reconnect the speakers. After reconnecting, turn on the unit, and then perform the YPAO measurement again.

E-7:No MIC

(E-7:NO MIC)

The YPAO microphone has

been removed.

Connect the YPAO microphone to the YPAO MIC jack firmly and select “RETRY (Retry)” in step 2 of “Procedure to exit YPAO” to restart the measurement.

E-8:No Signal

(E-8:NO SIGNAL)

The YPAO microphone

cannot detect test tones.

Connect the YPAO microphone to the YPAO MIC jack firmly and select “RETRY (Retry)” in step 2 of “Procedure to exit YPAO” to restart the measurement.

If this error occurs repeatedly, contact the nearest authorized Yamaha dealer or service center.

E-9:User Cancel

(E-9:CANCEL)

The measurement has

been canceled.

Select “PROCEED (Proceed)” in step 2 of “Procedure to exit YPAO” to resume the measurement. Select “RETRY (Retry)” to restart the measurement from

first.

E-10:Internal Err.

(E-10:INTERNAL)

An internal error has

occurred.

Follow “Procedure to exit YPAO” to exit YPAO, turn off and on the unit. Perform YPAO again. If this error occurs repeatedly, contact the nearest authorized

Yamaha dealer or service center.

1 2 3 4 5 6 7 8

Optimizing the speaker settings automatically (YPAO)

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 112 113

Comments to this Manuals

No comments

Yamaha RX-V571 Owner's Manual Page 32

Comments to this Manuals