Yamaha YSTMS50 Owner's Manual download pdf (Page 6)

Non skid pad

To prevent the speakers from sliding around, attach the supplied pads to the four points

on the bottom of each satellite speaker. Place the speaker on a stable, ﬂat surface.

Speciﬁcations

Type

.......................... Advanced Active Servo Technology

Output power

Satellite speakers...... 20 W + 20 W (1 kHz, 4

Ω

T.H.D.=10%)

Subwoofer................ 40 W (100 Hz, 5

Ω

at T.H.D.=10%)

Input sensitivity

.................200 mV (1 kHz, 4

Ω

at 20 W)

Input impedance

...............25 k

Ω

Frequency response

...........32 Hz to 20 kHz

Speaker unit

Satellite speakers

Tweeter................ 19 mm (3/4") dome, magnetic shielding

Midrange ........... 8 cm (3") cone, magnetic shielding

Subwoofer..................16 cm (6.5") cone, magnetic shielding

Power consumption

...........65W

Power supply

U.S.A. and Canada models.... AC 120 V, 60 Hz

Australia model.................... AC 240 V, 50 Hz

U.K. and Europe models...... AC 230 V, 50 Hz

General model............AC 110-120/220-240 V, 50/60 Hz

Dimensions (W

Satellite speakers ......97 (3.8")

159 (6.3")

178 (7") mm

Subwoofer.................350 (13.8")

210 (8.3")

321

(12.6") mm

Weight

Satellite speakers ......0.7 kg (1 lb. 9 oz.)

Subwoofer.................8.0 kg (17 lbs. 10 oz.)

Finish

YST-MS50 W...........Computer white

YST-MS50 B............Black

Accessories

3.5 mm stereo mini plug cable

1 (1.8m), RCA pin plug

cable

1 (1.8m), 8 pin plug cable

1 (1.8m), 8 pcs of non

skid pads

* Speciﬁcations subject to change without notice.

Troubleshooting

If the speakers fail to operate normally, check the following table. It lists common operation errors and simple mea-

sures that you can take to correct problems. If a problem cannot be corrected, or the symptom is not listed, discon-

nect the AC power cord and contact your authorized YAMAHA dealer or service center for help.

• Even if the (standby/on) button is turned off, a small amount of sound may be heard from the headphones if

the VOLUME control is set to max. This is normal.

FAULT CAUSE CURE

No sound comes

from the speakers or

subwoofer.

The AC power cord is not properly plugged

into the wall outlet.

Insert the AC power cord ﬁrmly into the wall outlet.

The main power switch on the subwoofer is

set to OFF.

Set the main power switch to ON.

The (standby/on) button is turned off. Turn on the (standby/on) button (the indicator

lights).

Connections are faulty or incomplete. Make the connections again, ﬁrmly, or use a differ-

ent cable.

The volume is set to minimum. Turn the speaker VOLUME control to the right to

increase the volume.

Turn the subwoofer VOLUME control to the right to

increase the volume.

The level of the signal being input is too low. Turn up the volume on the connected component.

Headphones are connected. Disconnect the headphones.

Sound is distorted. The level of the signal being input is too high. Turn down the volume on the connected component.

Noise. Connections are faulty or incomplete. Make the connections again, ﬁrmly, or use a differ-

ent cable.

Noise is heard when

the power is turned

on.

The power cord of this unit connected to

another unit’s SWITCHED AC OUTLET.

Connect the power cord to an UNSWITCHED AC

OUTLET.

Make sure to use the (standby/on) button on

this unit to turn on and off.

1 2 3 4 5 6 7

Comments to this Manuals

No comments

Yamaha YSTMS50 Owner's Manual Page 6

Comments to this Manuals

Related products and manuals for Unknown Yamaha YSTMS50