Yamaha BD-A1010 Owner's Manual download pdf (Page 41)

SETUP MENU

37 En

SETTINGS

English

■ Audio Setting

The default settings are marked with “

”.

Audio Output

Coaxial/Optical

You can select the output mode of COAXIAL jack and

OPTICAL terminal. For more details on output formats,

refer to “About the audio output formats” (p. 38).

HDMI

You can select the output mode of HDMI ternminal. For

details on setting items, see “Coaxial/Optical” (p. 37). For

more details on output formats, refer to “About the audio

output formats” (p. 38).

Bitstream

, PCM, Reencode, Off

– To output HD audio (such as Dolby TrueHD or

DTS-HD Master Audio) from HDMI terminal, set

Resolution to Auto or more than 720p (p. 35).

Downsampling

You can select digital audio signal down-sample

frequency. This function is effective for the audio signal

output from the COAXIAL jack/OPTICAL terminal.

DRC

You can set the DRC (Dynamic Range Compression)

(p. 44) to on/off/Auto. When set to Auto, DRC is

automatically turned on for a source with DRC

information in Dolby TrueHD format. DRC makes the

strong sound such as plosive sound lower, and

conversations more audible. It is useful when you watch

movies in the night.

Off

, On, Auto

SACD Output

SACD Priority

You can select a content played back from multi-channel

or stereo (2-channel) contents when a Hybrid SA-CD

(p. 4) including both is loaded.

Multi-ch

, 2-ch

HDMI Output

You can select audio signal output from HDMI terminal

when SA-CD is played back.

Speaker Setting

Configuration

You can set the output of 7.1 ch surround depending on

the connected speaker or amplifier.

1 Press 5/a to select a speaker you want to configure,

then press ENTER.

2 Adjust the figures below. Note that some of items are

not displayed depend on the selected speaker.

3 Press RETURN to go back to speaker selection.

2ch Downmix

You can select down mix method to analog 2-ch from

Stereo or Lt/Rt.

Post Process

Up Mix

You can multi-channelize the 2-channel audio signal. To

multi-channelize, select NEO6, then select Cinema or

Music mode.

Off

, NEO6

■ System Information

Software version and MAC address (p. 45) are displayed.

Bitstream Outputs digital signal without any processing.

Secondary Audio is not output.

PCM Outputs 2-channel PCM.

Reencode

Outputs Bitstream with Secondary Audio.

Off Mutes sound.

Note

48k

The highest sampling rate of digital PCM output is

48 kHz.

96k The highest sampling rate of digital PCM output is

96 kHz.

192k The highest sampling rate of digital PCM output is

192 kHz.

DSD

Outputs DSD raw signal. When this Player is

connected to DSD compatible AV receiver, this item

is recommended.

PCM Outputs PCM signal decoded by this Player.

Size When the woofer section of a speaker is 16 cm (6-1/

2 in) or larger, select Large. When smaller than 16

cm (6-1/2 in), select Small.

Large

, Small

Trim -12 to 0 dB (in 0.5 dB step)

The default setting is 0 dB.

Delay 0.5 to 10 m (in 0.5 m step)

The default setting is 3 m.

Disable When selected speaker is not in use, select Yes.

Yes, No

Stereo

Changes channel output to stereo, which only

delivers sound from the two front speakers.

Lt/Rt Select this item if this unit is connected to a Dolby

Pro Logic decoder. Sound from rear speakers is

mixed to the 2 ch stereo sound.

1 2 ... 36 37 38 39 40 41 42 43 44 45 46 ... 63 64

Comments to this Manuals

No comments

Yamaha BD-A1010 Owner's Manual Page 41

Comments to this Manuals

Related products and manuals for Blu-Ray players Yamaha BD-A1010