Yamaha RX-V750 Manual Page 85
- Page / 92
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
81
English
TROUBLESHOOTING
ADDITIONAL
INFORMATION
Problem Cause Remedy
Refer to
page
The sound suddenly
goes off.
The protection circuitry has been activated
because of a short circuit, etc.
Check that the impedance selector setting is correct.
24
Check that the speaker wires are not touching each
other and then turn this unit back on.
—
The sleep timer has turned the unit off. Turn on the power, and play the source again.
—
The sound is muted. Press MUTE to cancel a mute.
31
Only the speaker on
one side can be
heard.
Incorrect cable connections. Connect the cables properly. If the problem persists,
the cables may be defective.
13
Incorrect balance settings in the SET
MENU.
Adjust the SP LEVEL settings.
57
Only the center
speaker outputs
substantial sound.
When playing a monaural source with a
CINEMA DSP program, the source signal
is directed to the center channel, and the
front and surround speakers output effect
sounds.
No sound from the
effect speakers.
The sound field programs are turned off. Press STRAIGHT (EFFECT) to turn them on.
36
A Dolby Surround, Dolby Digital or DTS
decoding DSP program is being used with
material not encoded with Dolby
Surround, Dolby Digital or DTS.
Select another sound field program.
32
No sound from the
center speaker.
The output level of the center speaker is
set to minimum.
Raise the level of the center speaker.
57
“CENTER” in the SET MENU is set to
NONE.
Select the appropriate mode for your center speaker.
55
One of the Hi-Fi DSP programs (except
for 7ch Stereo) has been selected.
Select another sound field program.
32
No sound from the
surround speakers.
The output level of the surround speakers
is set to minimum.
Raise the output level of the surround speakers.
57
“SURR.LR” in the SET MENU is set to
NONE.
Select the appropriate speaker mode for the surround
L/R speakers.
56
A monaural source is being played with
STRAIGHT (EFFECT) set to
STRAIGHT.
Press STRAIGHT (EFFECT) to turn on the sound
fields. Then select another sound field program.
—
No sound from the
surround back
speakers.
Presence speakers are selected. Select surround back speakers in PR/SB SELECT.
56
“SURR.B” in the SET MENU is set to
NONE.
If the speaker mode for the surround left and right
speakers is set to NONE, the speaker mode for the
surround back speaker is automatically set to NONE.
Select the appropriate speaker mode for the surround
L/R speaker mode.
“SURR B L/R SP” in the SET MENU is
set to NONE.
Select LRG or SML.
56
No sound from the
subwoofer.
“BASS OUT” in the SET MENU is set to
FRONT when a Dolby Digital or DTS
signal is being played.
Select SWFR or BOTH.
57
“BASS OUT” in the SET MENU is set to
SWFR or FRONT when a 2-channel
source is being played.
Select BOTH.
57
The source does not contain low bass
signals.
00_RXV750_U_EN.book Page 81 Wednesday, November 5, 2003 3:38 PM
- AV Receiver 1
- IMPORTANT SAFETY INSTRUCTIONS 2
- CONTENTS 5
- FEATURES 6
- GETTING STARTED 7
- Remote control 10
- ■ U.K. and Europe models only 11
- Approximately 6 m (20 ft) 12
- Front panel display 13
- CONTROLS AND FUNCTIONS 14
- 12 3 47 865 15
- 90 A BC D E 15
- (U.S.A. model) 15
- 1.8 m (6 ft) 16
- Speaker connections 17
- SPEAKER SETUP 18
- Speaker layout 19
- CONNECTIONS 20
- Connecting video components 21
- MULTI CH INPUT 22
- PREPARATION 23
- Connecting audio components 24
- Connecting the antennas 26
- SELECTOR 27
- SET BEFORE POWER ON 28
- IMPEDANCE SELECTOR 28
- Front panel 29
- Optimizer microphone position 30
- Starting the setup 31
- RESULT:LEVEL 1 32
- AUTO SETUP 33
- PLAYBACK 34
- MULTI CH IN 36
- Sound field 37
- Program name 37
- /DTS 38
- Front panel Remote control 39
- STRAIGHT 40
- AUTO/MAN'L MONO 42
- Disappears 43
- Lights up 43
- Preset group 44
- MAN'L/AUTO FM 45
- E1 1:FM187.5kMHz 45
- Frequency 47
- PTY SEEK function 48
- EON function 48
- For movie/video sources 50
- Program Features Sources 51
- For music sources 52
- Full display Short display 53
- SLEEP indicator 53
- ■ Canceling the sleep timer 54
- Using the test tone 55
- SETUP MENU 56
- Using the setup menu 58
- 1 SOUND MENU 59
- PRESENCE 60
- BASS OUT 61
- CrossOver 61
- ■ Dynamic range F)D. RANGE 62
- 2 INPUT MENU 63
- B)INPUT MODE 64
- C)INPUT RENAME 64
- 3 OPTION MENU 65
- D)ZONE SET 66
- E)ZONE2 SET 66
- REMOTE CONTROL FEATURES 67
- Setting manufacturer codes 68
- 5 to 10 cm (2 to 4 in) 69
- Flashes alternately 70
- Changing source names in the 71
- Clearing function sets 72
- Clearing individual functions 73
- A/B. When the 74
- Zone 2 connections 75
- Second room 76
- This unit 76
- CDMD/CD-RTUNERV- AUX 77
- DVDVCR 1DTV/CBL DVR/VCR2 77
- Program No. Program name 78
- Parameters Parameter values 78
- 4 Press u / d to select 79
- 5 Press j / i to change 79
- ■ DSP LEVEL 80
- ■ DELAY (Delay) 80
- – 99 msec 80
- 60 dB 60 dB 60 dB 82
- TROUBLESHOOTING 84
- ADDITIONAL 85
- INFORMATION 85
- ■ Remote control 88
- GLOSSARY 89
- SPECIFICATIONS 91
Related products and manuals for AV receivers Yamaha RX-V750
AV receivers Yamaha RX-V2065 Owner's Manual
(114 pages)
(114 pages)
AV receivers Yamaha DSP-Z11 Manual
(150 pages)
(150 pages)
AV receivers Yamaha RX-V440 Owner's Manual
(66 pages)
(66 pages)
© 2020, manymanuals.com. All rights reserved. | 0.137 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals