Yamaha RX-V750 Manual download pdf (Page 62)

SETUP MENU

■ Speaker distance C)SP DISTANCE

Use this feature to manually input the distance of each

speaker and adjust the delay applied to respective channel.

Ideally, each speaker should be the same distance from the

main listening position. However, this is not possible in

most home situations. Thus, a certain amount of delay

must be applied to the sound from each speaker so that all

sound will arrive at the listening position at the same time.

Unit UNIT

Choices: meters (m), feet (ft)

Initial setting:

U.S.A. and Canada models: feet (ft)

Other models: meters (m)

• Select meters to input speaker distances in meters.

• Select feet to input speaker distances in feet.

Speaker distances

Choices: 0.3 to 24.00 m (1 to 80 ft)

• FRONT L adjusts the distance of the front left speaker.

Initial setting: 3.0 m (10.0 ft)

• FRONT R adjusts the distance of the front right

speaker. Initial setting: 3.0 m (10.0 ft)

• CENTER adjusts the distance of the center speaker.

Initial setting: 3.0 m (10.0 ft)

• SURR L adjusts the distance of the surround left

speaker. Initial setting: 3.0 m (10.0 ft)

• SURR R adjusts the distance of the surround right

speaker. Initial setting: 3.0 m (10.0 ft)

• SBL adjusts the distance of the surround back left

speaker. Initial setting: 2.10 m (7.0 ft)

• SBR adjusts the distance of the surround back right

speaker. Initial setting: 2.10 m (7.0 ft)

• SWFR adjusts the distance of the subwoofer. Initial

setting: 3.0 m (10.0 ft)

• PRES L adjusts the distance of the presence left

speaker. Initial setting: 3.0 m (10.0 ft)

• PRES R adjusts the distance of the presence right

speaker. Initial setting: 3.0 m (10.0 ft)

■ Graphic equalizer D)GRAPHIC EQ

Use this feature to adjust the built-in 5-band graphic

equalizer for the center channel so that the tonal quality of

the center speaker matches that of the left and right main

speakers.

Choices: –6 to +6 dB

You can adjust 5 frequency bands: 100Hz, 300Hz, 1kHz,

3kHz, 10kHz

■ Low-frequency effect level E)LFE LEVEL

Use to adjust the output level of the LFE (low-frequency

effect) channel according to the capacity of your

subwoofer or headphones. The LFE channel carries low-

frequency special effects which are only added to certain

scenes. This setting is effective only when this unit

decodes Dolby Digital or DTS signals.

Choices: –20 to 0 dB

Speaker SP LFE

Select to adjust the speaker LFE level.

Headphone HP LFE

Select to adjust the headphone LFE level.

Depending on the settings of LFE LEVEL, some signals may not

be output from the SUBWOOFER jack.

■ Dynamic range F)D. RANGE

Use to select the amount of dynamic range compression to

be applied to your speakers or headphones. This setting is

effective only when the unit is decoding Dolby Digital and

DTS signals.

Choices: MIN (minimum), STD (standard),

MAX (maximum)

SP D.R

Select to adjust the speaker compression.

HP D.R

Select to adjust the headphone compression.

• Select MAX for feature films.

• Select STD for general use.

• Select MIN for listening to sources at low volume

levels.

. UNIT;;;;;;meters

FRONTL;;;;2.30m

FRONTR;;;;2.30m

CENTER;;;;;2.00m

: Up/Down

: Adjust

-/+

C)SP

DISTANCE

Note

. SPEAKER;;;;;;0dB

HEADPHONE;;;;0dB

/ : Up/Down

-/+ : Adjust

E)LFE

LEVEL

. SP: MIN STD[MAX

HP: MIN STD[MAX

/ : Up/Down

-/+ : Adjust

F)D. RANGE

00_RXV750_U_EN.book Page 58 Wednesday, November 5, 2003 3:38 PM

1 2 ... 57 58 59 60 61 62 63 64 65 66 67 ... 91 92

Comments to this Manuals

No comments

Yamaha RX-V750 Manual Page 62

Comments to this Manuals

Related products and manuals for AV receivers Yamaha RX-V750