Yamaha MG206c-USB Owner's Manual download pdf (Page 14)

Front & Rear Panels

MG206C/MG166CX/MG166C Owner’s Manual

Reference

A AUX, EFFECT Control

Adjusts the level of the signal sent from the channel to the

AUX and EFFECT buses. These knobs should generally be

set close to the “▼” position. These controls send either the

signal from immediately prior to the channel fader (pre-fader

signal) or the signal after the channel fader (post-fader sig-

nal) to the corresponding buses. The types of signals sent by

the AUX and EFFECT controls on each mixer model are as

follows:

• MG206C

AUX1: Pre-fader

AUX2, 3: Pre-fader/post-fader (determined by the AUX

PRE switch

AUX4: Post-fader

• MG166CX

AUX1: Pre-fader

AUX2: Pre-fader/post-fader (determined by the AUX

PRE switch

EFFECT: Post-fader

• MG166C

AUX1: Pre-fader

AUX2: Pre-fader/post-fader (determines by the AUX

PRE switch

AUX3: Post-fader

•To send the signal to the STEREO bus engage the

ON switch ( ).

• On stereo channels, the L (odd) and R (even) input

signals are mixed and sent to the AUX and

EFFECT buses.

B AUX PRE Switch

Selects whether the pre-fader or the post-fader signal is fed

to the AUX buses. If the switch is on ( ), the mixer sends

the pre-fader signal to the AUX buses, so that AUX outputs

are not affected by the channel fader

I. If the switch is off

() the mixer sends the post-fader signal to the AUX

buses.

C PAN Control

PAN/BAL Control

BAL Control

The PAN control determines the stereo positioning of the

channel signal on the GROUP 1/2 and GROUP 3/4 buses or

on the STEREO L/R bus. The BAL control knob sets the

balance between left and right channels. Signals input to the

L input (odd channel) go to the GROUP 1 or 3 buses or to

the STEREO L bus; signals input to the R input (even chan-

nel) go to the GROUP 2 or 4 buses or the STEREO R bus.

On channels where this knob provides both PAN and

BAL control, the knob operates as a PAN control

when input is received via the MIC jack or L (MONO)

input only, and as a BAL control when input is

received via both L and R inputs.

D ON Switch

Turn this switch on to send the signal to the buses. The

switch lights orange when on.

E PFL (Pre-Fader Listen) Switch

This switch lets you monitor the channel’s pre-fader signal.

Press the switch in ( ) so that it lights to turn it on. When

the switch is on the channel pre-fader signal is output to the

PHONES and MONITOR OUT jacks for monitoring.

F 1-2 Switch

This switch assigns the channel’s signal to the GROUP 1/2

bus.

To send the signal to the GROUP 1/2 bus turn the

ON switch on ( ).

G 3-4 Switch

This switch assigns the channel’s signal to the GROUP 3/4

bus.

To send the signal to the GROUP 3/4 bus turn the

ON switch on ( ).

H ST Switch

This switch assigns the channel’s signal to the STEREO L/R

bus.

To send the signal to the STEREO bus turn the ON

switch on ( ).

I Channel Fader

Adjusts the level of the channel signal. Use these faders to

adjust the balance between the various channels.

Set the fader sliders for unused channels all the way

down to minimize noise.

NOTE

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 28 29

Comments to this Manuals

No comments

Yamaha MG206c-USB Owner's Manual Page 14

Comments to this Manuals

Related products and manuals for Audio mixers Yamaha MG206c-USB