Yamaha CL5 Datasheet download pdf (Page 3)

1053

299

130

201

667

839

201

130

299

667

389

535

374

299

201

130

667

648

CL Series

*1 Total harmonic distortion is measured with a 18dB/Oct ﬁlter @80kHz.

*2 Hum & noise level is measured with a 6dB/oct ﬁlter @12.7kHz; equivalent to 20kHz ﬁlter with

inﬁnite dB/Oct attenuation.

*3 Crosstalk is measured with a 30 dB/octave ﬁlter @22kHz.

** Excluded MBCL optional meter bridge.

*1. Input pins: Internal TTL-level pull-up

resistors provided (47kΩ). Output pins:

Open-drain output (Vmax = 12V, max.

sink current/pin = 75mA)

Power pins: Output voltage Vp = 5V,

max. output current Imax = 300mA

*2. Pin 4 = +12V, Pin 3 = GND, lamp

rating 5W. Software voltage control.

unit : mm

CL5 CL3 CL1

GENERAL SPECIFICATIONS

Sampling frequency rate Internal: 44.1kHz, 48kHz

External: 44.1kHz (+4.1667%, +0.1%, -0.1%, -4.0%) ±200ppm

48kHz (+4.1667%, +0.1%, -0.1%, -4.0%) ±200ppm

Signal Delay Less than 2.5 ms OMNI IN to OMNI OUT (@fs=48kHz)

Total harmonic distortion*

OMNI IN to OMNI OUT

Input Gain=Min.

Less than 0.05% 20Hz to 20kHz @+4dBu into 600Ω

Frequency response

CH INPUT to OMNI OUT

+0.5, -1.5dB 20Hz to 20kHz, refer to +4dBu output @1kHz,

OMNI IN to OMNI OUT

Dynamic range

(maximum level to noise level)

112dB typ., DA Converter,

108dB typ., OMNI IN to OMNI OUT, Input Gain = Min.

Hum & noise level*

(20Hz to 20kHz), Rs=150Ω

-128dBu Equivalent input noise, Input Gain=Max.,

-84dBu Residual output noise, ST master off

Crosstalk (@1kHz)

Input Gain=Min.

-100dB*

, Adjacent OMNI IN/OMNI OUT channels

Phantom Power +48V

Power requirements AC110V-240V, 50/60Hz

Power consumption CL5/CL3/CL1: 170W, Internal Power Supply

CL5/CL3/CL1: 200W, Simultaneous use of Internal PSU and

External PW800W

Dimensions (W x H x D) CL5: 1053 x 299 x 667mm (41.5" x 11.8" x 26.3")

CL3: 839 x 299** x 667mm (33.1" x 11.8" x 26.3")

CL1: 648 x 299** x 667mm (25.5" x 11.8" x 26.3")

Weight CL5: 36kg (79.4lbs)

CL3: 29kg (63.9lbs)

CL1: 24kg (52.9lbs)

ANALOG INPUT SPECIFICATIONS

ANALOG OUTPUT SPECIFICATIONS

Input terminal

GAIN

Actual

source

impedance

For use with

nominal

Input level

Connector

Sensitivity Nominal

Max.

before clip

OMNI IN 1-8

+66dB

10kΩ

50-600Ω Mics

& 600Ω Lines

-82dBu -62dBu -42dBu

XLR3-31 type*

+18dB -34dBu -14dBu +6dBu

+17dB

3kΩ

-33dBu -13dBu +7dBu

-6dB -10dBu +10dBu +30dBu

TALKBACK

+64dB

10kΩ

50-600Ω Mics

& 600Ω Lines

-70dBu -60dBu -40dBu

XLR3-31 type*

+20dB -26dBu -16dBu +4dBu

Output terminal

Actual source

impedance

For use with

nominal

GAIN SW

Output terminals

Connector

Nominal

Max.

before clip

OMNI OUT 1-8 75Ω 600Ω Lines

+24dB +4dBu +24dBu

XLR3-32 type*

+18dB -2dBu +18dBu

PHONES 15Ω

8Ω Phones — 75mW 150mW

ST Phone Jack**

40Ω Phones — 65mW 150mW

DIGITAL I/O SPECIFICATIONS

DIGITAL OUTPUT SPECIFICATIONS

I/O Slot (1-3) SPECIFICATIONS

Terminal Format

Data length

Level Audio Connector

Primary/Secondary Dante

24bit or 32bit

1000Base-T

64ch Input/64ch Output

@48kHz

etherCON Cat5e

Terminal Format

Data length

Level Connector

DIGITAL OUT AES/EBU

AES/EBU Professional

Use

24bit RS422 XLR3-32 type*

Each I/O Slot accepts a Mini-YGDAI card. Only Slot1 has a serial interface.

CONTROL I/O SPECIFICATIONS

Terminal Format Level

MIDI

IN MIDI —

OUT MIDI —

WORD CLOCK

IN — TTL/75Ω terminated

OUT — TTL/75Ω

GPI (5IN/5OUT) — —

NETWORK IEEE802.3 10BASE-T/100Base-TX/

LAMP (CL5=3, CL3=2, CL1=1) — 0V - 12V

USB HOST USB 2.0 —

EXT DC IN — —

Meter Bridge (CL3/CL1 only) — —

DIMENSIONS

1 2 3 4 5

Comments to this Manuals

No comments

Yamaha CL5 Datasheet Page 3

Comments to this Manuals

Related products and manuals for Audio equalizers Yamaha CL5