Yamaha S30 User Manual download pdf (Page 27)

3) TRANSMIT/RECEIVE DATA

(3-1) CHANNEL VOICE MESSAGES

(3-1-1) NOTE OFF

STATUS 1000nnnn(8nH) n = 0 ~ 15 CHANNEL NUMBER

NOTE NUMBER 0kkkkkkk k = 0 (C-2) ~ 127 (G8)

VELOCITY 0vvvvvvv ignores "v"

Receive only.

(3-1-2) NOTE ON/OFF

STATUS 1001nnnn(9nH) n = 0 ~ 15 CHANNEL NUMBER

NOTE NUMBER 0kkkkkkk k = 0 (C-2) ~ 127 (G8)

VELOCITY 0vvvvvvv(v≠0) NOTE ON

0vvvvvvv(v=0) NOTE OFF

(3-1-3) CONTROL CHANGE

STATUS 1011nnnn(BnH) n = 0 ~ 15 CHANNEL NUMBER

CONTROL NUMBER 0ccccccc

CONTROL VALUE 0vvvvvvv

* TRANSMITTED CONTROL NUMBER

c = 0 BANK SEL MSB ; v = 0,63,127 *3

c = 32 BANK SEL LSB ; v = 0,1,8,9,24,25,32,40,41,64,65 *3

c = 1 MODULATION ; v = 0 - 127

c = 0..95 ASSIGNABLE CONTROLLER ; v = 0 - 127 *6

The Sequencer Part will play back all the recorded control change messages.

* RECEIVED CONTROL NUMBER

c = 0 BANK SEL MSB ; v = 0 - 127 *3

c = 32 BANK SEL LSB ; v = 0 - 127 *3

c = 1 MODULATION ; v = 0 - 127

c = 5 PORTAMENTO TIME ; v = 0 - 127 *2

c = 6 DATA ENTRY MSB ; v = 0 - 127 *1

c = 38 DATA ENTRY LSB ; v = 0 - 127 *1

c = 7 MAIN VOLUME ; v = 0 - 127

c = 10 PAN ; v = 0 - 127

c = 11 EXPRESSION ; v = 0 - 127

c = 31 EG SUSTAIN LEVEL ; v = 0:-64 - 64:0 - 127:+63 *2,*5

c = 64 SUSTAIN SWITCH ; v = 0-63:OFF , 64-127:ON *2

c = 65 PORTAMENTO SWITCH ; v = 0-63:OFF , 64-127:ON *2

c = 66 SOSTENUTO ; v = 0-63:OFF , 64-127:ON *2

c = 71 HARMONIC CONTENT ; v = 0:-64 - 64:0 - 127:+63

c = 72 EG RELEASE TIME ; v = 0:-64 - 64:0 - 127:+63 *2

c = 73 EG ATTACK TIME ; v = 0:-64 - 64:0 - 127:+63

c = 74 BRIGHTNESS ; v = 0:-64 - 64:0 - 127:+63

c = 75 EG DECAY TIME ; v = 0:-64 - 64:0 - 127:+63

c = 91 EFFECT1 DEPTH ; v = 0 - 127

c = 93 EFFECT3 DEPTH ; v = 0 - 127

c = 96 DATA ENTRY INC ; v = 127 *1

c = 97 DATA ENTRY DEC ; v = 127 *1

c = 0..95 ASSIGNABLE CONTROLLER ; v = 0 - 127 *6

c = 0..95 ARPEGGIO SW ; v = 0-63:OFF , 64-127:ON *6

c = 0..95 ARPEGGIO HOLD ; v = 0-63:OFF , 64-127:ON *6

*1 Used only when a value is set using RPN.

*2 Invalid with Drum Voices.

*3 Relation between BANK CHANGE and PROGRAM is as follows:

CATEGORY |MSB |LSB |PROGRAM No

Displayed on LCD

----------------------------------+--------+--------+---------------------------

Normal Voice Internal |0 |0 |0..127 (1..128)

Drum Voice Internal |127 |0 |0..1 (1..2)

Normal Voice Preset 1 |63 |0 |0..127 (1..128)

Preset 2 |63 |1 |0..127 (1..128)

Internal |63 |8 |0..127 (1..128)

External |63 |9 |0..127 (1..128)

Plug-in Voice Plug-in |63 |25 |0..63 (1..64)

Drum Voice Preset |63 |32 |0..7 (1..8)

Internal |63 |40 |0..1 (1..2)

External |63 |41 |0..1 (1..2)

Performance Internal |63 |64 |0..127 (1..128)

External |63 |65 |0..63 (1..64)

*5 Transmitted/received only when MODE2 is selected in CONTROL CHANGE MODE.

*6 The default CONTROL NUMBERs of ASSIGNABLE CONTROLLER are as follows:

FOOT CONTROLLER 11

KNOB 1 16

KNOB 2 17

KNOB A 18

KNOB B 19

KNOB C 20

RIBBON CONTROLLER 22 (Receive only)

CONTROL SLIDER 7

FOOT SWITCH 64

ARPEGGIO HOLD 89 (Receive only)

ARPEGGIO SWITCH 90 (Receive only)

PORTAMENTO TIME sets the time it takes for the pitch to reach the next note played

when PORTAMENTO SWITCH is set to on.

PAN position relatively changes according to the preset value for each voice.

EFFECT1 DEPTH controls reverb send level.

EFFECT3 DEPTH controls chorus send level.

HARMONIC CONTENT adjusts the resonance preset for each voice.

Setting a value adds to or subtracts from the center value, 64, since it is an offset

parameter.

The larger the value more resonant sound will be produced. The effective range may be

narrower than the range you can designate depending on the selected voice.

The parameters, EG ATTACK TIME, EG DECAY TIME, EG SUSTAIN LEVEL, EG RELEASE TIME

adjust the envelopes preset for each voice.

Setting these values add to or subtract from the center value, 64, since these are

offset parameters.

BRIGHTNESS adjusts the cutoff frequency preset for each voice.

Setting a value adds to or subtracts from the center value, 64, since it is an offset

parameter.

The smaller the value the cutoff frequency will be lowered. The effective range may be

narrower than the range you can designate depending on the selected voice.

Bank Select will be actually executed when the Program Change message is received.

Bank Select and Program Change numbers that are not supported by Yamaha will be

ignored.

(3-1-4) PROGRAM CHANGE

STATUS 1100nnnn(CnH) n = 0 ~ 15 CHANNEL NUMBER

PROGRAM NUMBER 0ppppppp p = 0 ~ 127

(3-1-5) CHANNEL AFTER TOUCH

STATUS 1101nnnn(DnH) n = 0 ~ 15 CHANNEL NUMBER

VALUE 0vvvvvvv v = 0 ~ 127 AFTER TOUCH VALUE

(3-1-6) PITCH BEND CHANGE

STATUS 1110nnnn(EnH) n = 0 ~ 15 CHANNEL NUMBER

LSB 0vvvvvvv PITCH BEND CHANGE LSB

MSB 0vvvvvvv PITCH BEND CHANGE MSB

Transmitted with a resolution of 7 bits.

(3-2) CHANNEL MODE MESSAGES

STATUS 1011nnnn(BnH) n = 0 ~ 15 CHANNEL NUMBER

CONTROL NUMBER 0ccccccc c = CONTROL NUMBER

CONTROL VALUE 0vvvvvvv v = DATA VALUE

(3-2-1) ALL SOUNDS OFF (CONTROL NUMBER = 78H , DATA VALUE = 0)

All the sounds currently played including the channel messages such as note-on and

hold-on in a certain channel are muted when receiving this message.

(3-2-2)

RESET ALL CONTROLLERS

(CONTROL NUMBER = 79H , DATA VALUE = 0)

Resets the values set for the following controllers.

PITCH BEND CHANGE 0 (center)

CHANNEL AFTER TOUCH 0 (minimum)

MODULATION 0 (minimum)

EXPRESSION 127 (maximum)

FOOT CONTROLLER 127 (maximum)

KNOB 1 0 (center)

KNOB 2 0 (center)

SUSTAIN SWITCH 0 (off)

SOSTENUTO SWITCH 0 (off)

RPN Not assigned; No change

Doesn’t reset the following data:

PROGRAM CHANGE, BANK SELECT MSB/LSB, VOLUME, PAN.

HARMONIC CONTENT, SUSTAIN LEVEL, RELEASE TIME, ATTACK TIME, DECAY TIME, BRIGHTNESS

EFFECT SEND LEVEL 1, EFFECT SEND LEVEL 3, PORTAMENTO SWITCH

PITCH BEND SENSITIVITY, FINE TUNING, COARSE TUNING

ASSIGNABLE CONTROLLER

(3-2-3) ALL NOTES OFF (CONTROL NUMBER = 7BH , DATA VALUE = 0)

All the notes currently set to on in certain channel(s) are muted when receiving

this message. However, if Sustain or Sostenuto is on, notes will continue sounding

until these are turned off.

(3-2-4) OMNI MODE OFF (CONTROL NUMBER = 7CH , DATA VALUE = 0)

Performs the same function as when receiving ALL NOTES OFF.

Sets VOICE RECEIVE CHANNEL to "OMNI OFF," channel 1.

(3-2-5) OMNI MODE ON (CONTROL NUMBER = 7DH , DATA VALUE = 0)

Performs the same function as when receiving ALL NOTES OFF.

Sets VOICE RECEIVE CHANNEL to "OMNI ON."

(3-2-6) MONO (CONTROL NUMBER = 7EH , DATA VALUE = 0..16)

Performs the same function as when receiving ALL SOUNDS OFF. If the 3rd byte (mono)

is within 0 through 16, the channel will be Mode4(m = 1).

In VOICE MODE, the mode can be Mode2(m=1) according to VOICE RECEIVE CHANNEL.

(3-2-7) POLY (CONTROL NUMBER = 7FH , DATA VALUE = 0)

Performs the same function as when receiving ALL SOUNDS OFF. The channel will be

Mode3.

In VOICE MODE, the mode can be Mode1 according to VOICE RECEIVE CHANNEL.

(3-3) REGISTERED PARAMETER NUMBER

STATUS 1011nnnn(BnH) n = 0 ~ 15 CHANNEL NUMBER

LSB 01100100(64H)

RPN LSB 0ppppppp p = RPN LSB(Refer to the table as shown below)

MSB 01100101(65H)

RPN MSB 0qqqqqqq q = RPN MSB(Refer to the table as shown below)

DATA ENTRY MSB 00000110(06H)

DATA VALUE 0mmmmmmm m = Data Value

DATA ENTRY LSB 00100110(26H)

DATA VALUE 0lllllll l = Data Value

First, designate the parameter using RPN MSB/LSB numbers. Then, set its value with

data entry MSB/LSB.

RPN D.ENTRY

LSB MSB MSB LSB PARAMETER NAME DATA RANGE

00H 00H mmH --- PITCH BEND SENSITIVITY 00H - 18H (0 - 24 semitones)

01H 00H mmH llH MASTER FINE TUNE {mmH,llH}={00H,00H}-{40H,00H}-{7FH,7FH}

(-8192*100/8192) - 0 - (+8192*100/8192)

02H 00H mmH --- MASTER COARSE TUNE 28H - 40H - 58H (-24 - 0 - +24 semitones)

7FH 7FH --- --- RPN RESET RPN numbers will be left not designated.

The internal values are not affected.

(3-4) NON-REGISTERED PARAMETER NUMBER

There are no applicable parameters.

(3-5) SYSTEM REAL TIME MESSAGES

(3-5-1) ACTIVE SENSING

STATUS 11111110(FEH)

Transmitted at every 200 msec.

Once this code is received, the instrument starts sensing. When no status nor data

is received for over approximately 350 ms, MIDI receiving buffer will be cleared,

and the sounds currently played and the sustain switch are forcibly turned off. In

this case, each control data will be reset to a certain value.

(3-6) SYSTEM EXCLUSIVE MESSAGE

(3-6-1)UNIVERSAL NON REALTIME MESSAGE

(3-6-1-1)GENERAL MIDI MODE ON

F0H 7EH 7FH 09H 01H F7H

Received only when SYSTEM Receive GM/XG on is set to on in PERFORMANCE MODE. The

Part values will be reset according to the SYSTEM Internal Part settings.

S30_DL.qx 3/14/00 5:32 PM Page 27

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 39 40

Comments to this Manuals

No comments

Yamaha S30 User Manual Page 27

Comments to this Manuals

Related products and manuals for Synthesizer Yamaha S30