Yamaha 150S User Manual download pdf

MODEL AW YAMAHA SERIES 150 HP

ASSEMBLY INSTRUCTIONS

IN-LINE 4 CYLINDER, 4 STROKE 163 CU. IN.

1. Place the engine on the transom of your boat so that it is mounted vertically, in the normal

fashion. Remove the bolts holding the gearbox to the exhaust housing and remove the gearbox

assembly.

2. Remove the water pump assembly from the propeller drive, including the lower stainless steel

plate, dowel pins, and impeller drive key.

3. Install the jet driveshaft assembly into the spiral pump housing locking it in place with the four

5/16-18 x 1 bolts with lock washers. Use grease on the threads. Tighten to 15 Ft-Lbs.

4. Install the water pump assembly on top of the 3/4” thick aluminum adapter and stainless steel

plate. Be sure also, to install the water pump impeller drive key removed from the propeller

drive. Lock in place using four 5/16 -18 x 2 1/2 bolts and lock washers. Grease the threads.

Tighten to 10 Ft -Lbs. The tapered thrust ring assembly above the water pump on the

propeller drive is not used on the jet drive.

5. The large 3/4” adapter plate is attached to the exhaust housin g to hold the jet drive. A 1/4 x

2” plastic shift rod guide in the front of the plate guides the disconnected shift rod. Two 8 x

12MM dowels locate the plate, seven M10 x 34MM bolts with lock washers secure it. Grease

the bolt threads and the end of the pin where it slides in the shift rod. Tighten to 22 Ft-Lbs.

6. Next, attach the jet drive to the motor. Two 3/16 x 1/2 dowel pins center the jet drive on the

adapter plate. Four 3/8-16 bolts from below and one 3/8-16 x 1-1/2 bolt from above rear with

lock washers are used. Select the lower bolt lengths to suit the different counter bore depths so

that all bolts enter the adapter plate the same depth. The upper rear bolt is reached through the

trim tab opening in the motor exhaust housing.

Grease the bolt threads, driveshaft spline generously, and rubber water tube pilot and guide

the jet into place. Tighten to 22 Ft-Lbs.

7. Next, install the impeller. Grease the shaft threads, key and impeller bore. Place the plastic

sleeve inside the impeller, hold the key in the nose of the impeller with your forefinger and slide

onto the driveshaft. Install the seven shim washers, rubber washer and cup, and nut retainer on

the shaft, up against the impeller, and bring the nut up snug by hand.

Then bump the nut up snug with a wrench. If the ears of the retainer do not line up with the

flats on the nut, spin the nut off, turn the retainer over and tighten the nut again. In one of

these two positions you will have alignment and can fold the ears up against the nut to retain it.

The flat in the retainer is angled to the ears to allow this.

When, after use in sand and gravel, the blade clearance becomes more than about 1/32 ”

between the impeller edge and the water intake liner, one or more of the shim washers can be

transferred from the bottom stack to the top of the impeller, which moves the impeller down

into the tapered casing to reduce the clearance.

Shims should not be used above the impeller on new installations where no wear has

occurred unless the blade clearance exceeds 1/32 inch. Insufficient blade clearance will do

more harm than good from any performance gains it might provide.

1 2 3 4 5 6

Summary of Contents

Page 1 - ASSEMBLY INSTRUCTIONS

MODEL AW YAMAHA SERIES 150 HP ASSEMBLY INSTRUCTIONS IN-LINE 4 CYLINDER, 4 STROKE 163 CU. IN. 1 1. Place the engine on the transom of your boat

Page 2

MODEL AW YAMAHA SERIES 150 HP ASSEMBLY INSTRUCTIONS IN-LINE 4 CYLINDER, 4 STROKE 163 CU. IN. 2 8. Place the intake casing in position with the lo

Page 3

MODEL AW YAMAHA SERIES 150 HP ASSEMBLY INSTRUCTIONS IN-LINE 4 CYLINDER, 4 STROKE 163 CU. IN. 3 CAUTION When starting the engine for the first ti

Page 4

MAINTENANCE AND LUBRICATION OUTBOARD JET DRIVE BEARING LUBRICATION A grease gun and tube of grease is supplied with your jet drive. We recommend gr

Page 5

Page 6 - MODEL AW YAMAHA 150HP

MODEL AW YAMAHA 150HPIN-LINE 4 CYL. 4 STROKE 163 CU. IN.REF QTY PART DESCRIPTION REF QTY PART DESCRIPTIONNO. NO.1 1 938 PUMP ADAPTER AA 51 4 517 SPI

Comments to this Manuals

No comments

Yamaha 150S User Manual

Browse online or download User Manual for Musical Instruments Yamaha 150S. MODEL AW YAMAHA SERIES 150 HP ASSEMBLY

Summary of Contents

Comments to this Manuals

Related products and manuals for Musical Instruments Yamaha 150S