Yamaha ROADLINER XV19SC Instruction Manual download pdf (Page 2)

HOW IT WORKS

ENTERING VALUES

1. Remove Fuelpak clear case cover by removing all four screws, save hardware.

2. Turn on

main power with key, but do not start engine. Fuelpak display should light up, if not, turn power

off and verify the connectors are fully seated.

3. Refer to Fuelpak Setting Reference to locate the Setting Values speciﬁc to your bike and exhaust system. If

you do not ﬁnd your setting, visit fuelpakﬁ.com or call tech support at

(562) 921-0071.

4. Starting with mode 1 selected, press the value (+) or the value (-) buttons to input the correct value as

indicated in your Setting Value. After entering your ﬁrst value, press the mode select button to move to mode

2 and enter the value. Continue until you have entered the value for each of the ﬁrst 18 mode positions.

Each time the value (+) is pressed, the value increases by one number. Each time the value (-) is pressed, the

value decreases by one number. (Please refer to the “How It Works” section directly above if you have

questions about this step.

5. As the next procedure, after you have entered in your values for the ﬁrst 18 modes, press the

mode select button to move to mode 19. Fully twist open the throttle and return to idle

position to calibrate the Fuelpak to your bike.

6. By pressing the mode select button twice, move to mode 21 and verify that it reads “0” with the throttle

closed, “50” at approximately half-throttle and “99” when fully opened; if not, repeat step 5. Do not proceed

to step 7 until mode 21 is veriﬁed.

7. Enter any other mode values as required for your application.

8. Turn off power.

9. Reinstall clear cover, tuck Fuelpak under seat area and reinstall seat.

10. You are now ready to ride.

WARRANTY INFORMATION

WARRANTY: Your Fuelpak unit is warranted against defects

in materials and workmanship for the period of 90 days from

the original retail purchase. In the event of an alleged defect

in material or workmanship, Fuelpak’s responsibility is strictly

limited to repair or replace the defective product. Fuelpak

shall not be responsible for (a) labor, transportation, or other

incidental charges; (b) consequential or other damages

incurred by use of any product. Fuelpak offers no other

warranty beyond this limited warranty. This limited warranty

does not apply to products which have been (a) modiﬁed

or altered in any way; (b) subjected to adverse conditions,

such as misuse, neglect, accident, improper installation

or adjustment, contaminants, corrosion, or faulty repair;

or (c) used in applications other than those recommended by

Fuelpak. To initiate a warranty process, the consumer must ﬁrst

call technical support to receive a return authorization number.

The product must be returned to Fuelpak complete with a dated

receipt and a return authorization number.

Fuelpak

Attn: Warranty Claims

13861 Rosecrans Avenue

Santa Fe Springs, CA 90670

(562) 921-0071

P/N 51736 053107

TECH

SUPPORT

IN THE EVENT OF A MALFUNCTION, PLEASE CHECK THE FOLLOWING

FUEL INJECTION MANAGEMENT SYSTEM

1. Turn off main and handlebar switches then verify all

connectors are fully seated.

2. Be sure setting values are correct for your application.

3. Verify throttle calibration, step 5 in Entering Values.

4. Check harness for cuts, scrapes or abrasions.

5. Make sure the battery is fully charged and the

charging system is operating correctly.

6. Call technical support at (562) 921-0071

1 2

Comments to this Manuals

No comments

Yamaha ROADLINER XV19SC Instruction Manual Page 2

Comments to this Manuals

Related products and manuals for Motorcycles Yamaha ROADLINER XV19SC