Yamaha RX-A820 Manual Page 114
- Page / 161
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
APPENDIX ➤ Troubleshooting En 114
Video
No sound from the TV (when HDMI Control is
used).
The TV is set to output audio from the TV speakers.
Change the audio output setting on your TV so that the TV audio is output from the
speakers connected to the unit.
(If the TV is connected to the unit with an audio cable)
The TV audio input setting does not match the actual connection.
Use “TV Audio Input” in the “Setup” menu to select the correct audio input jack
(p.93).
(If you are trying to use ARC)
ARC is disabled on the unit or TV.
Set “ARC” in the “Setup” menu to “On” (p.94). Also, enable ARC on the TV.
Only the front speakers work on multichannel
audio.
The playback device is set to output 2-channel audio (such as
PCM) only.
To check it, use “Audio Signal” in the “Information” menu (p.101). If necessary,
change the digital audio output setting on the playback device.
Noise/hum is heard.
The unit is too close to another digital or radio frequency device. Move the unit further away from the device.
The cable connecting the unit and playback device is defective. If there is no problem with the connection, replace with another cable.
The sound is distorted.
The volume of the unit is too high. Turn down the volume. If “ECO Mode” is set to “On”, set it to “Off” (p.99).
A device connected to the unit’s output jacks is not turned on. (This
may happen due to the nature of AV receivers.)
Turn on all devices connected to the unit’s output jacks.
Problem Cause Remedy
Problem Cause Remedy
No video.
Another input source is selected on the unit. Select an appropriate input source with the input selection keys.
Another input source is selected on the TV. Switch the TV input to display the video from the unit.
The video signal output from the unit is not supported by the TV. Set “MON.CHK” in the “ADVANCED SETUP” menu to “YES” (p.103).
The cable connecting the unit and TV (or playback device) is
defective.
If there is no problem with the connection, replace with another cable.
No video from the playback device (connected to
the unit with HDMI).
The input video signal (resolution) is not supported by the unit.
To check the information about the current video signal (resolution), use “Video
Signal” in the “Information” menu (p.101). For information about video signals
supported by the unit, see “HDMI signal compatibility” (p.124).
The TV does not support HDCP (High-bandwidth Digital Content
Protection).
Refer to the instruction manuals for the TV and check the TV’s specifications.
The number of devices connected to the HDMI OUT jack is over
the limit.
Disconnect some of the HDMI devices.
The menu of the unit is not displayed on the TV.
The TV is not connected to the unit via HDMI.
You can display the menu of the unit on the TV only when they are connected with
an HDMI cable. If necessary, use an HDMI cable to connect them (p.21 to 24).
Another input source is selected on the TV. Switch the TV input to display the video from the unit (HDMI OUT jack).
- Owner’s Manual 1
- CONTENTS 2
- CONFIGURATIONS 78 3
- APPENDIX 111 4
- Accessories 5
- FEATURES 6
- Full of useful functions! 7
- Useful tips 7
- Part names and functions 8
- Front display (indicators) 9
- Rear panel 10
- Remote control 11
- General setup procedure 12
- 1 Placing speakers 13
- 7.1+2-channel system 14
- 6.1-channel system 14
- 5.1-channel system 15
- 4.1-channel system 15
- 3.1-channel system 15
- 2.1-channel system 15
- 2 Connecting speakers 17
- ■ Connecting speaker cables 18
- ■ Connecting the subwoofer 18
- 3 4 5 6 7 8 9 10 19
- ■ Video/audio jacks 20
- ■ Video jacks 20
- ■ Audio jacks 20
- 3 Connecting a TV 21
- ON SCREEN 22
- TV connection 23
- NETWORKDC OUT 24
- MONITOR O 25
- ITOR OUT 25
- ■ HDMI connection 26
- ■ Component video connection 26
- ■ Composite video connection 27
- Playback device connections 28
- 5 6 7 8 9 10 29
- 6 Connecting to a network 30
- Connecting recording devices 31
- TRIGGER OUT 32
- 8 Connecting the power cable 33
- Chinese 34
- Language setting 34
- RECEIVER z 35
- (multi/single) 36
- (single measure) 37
- (multi measure) 38
- The following screen appears 39
- Automatic speaker setup 40
- Error messages 41
- Warning messages 42
- PLAYBACK 43
- SETComplete 44
- Sci-Fi 46
- ❑ CLASSICAL 47
- ❑ LIVE/CLUB 47
- ❑ STEREO 47
- Hall in Vienna 48
- ProLogic 49
- Enhancer On 50
- FM87.50MHz 51
- FM98.50MHz 51
- ■ Registering a radio station 52
- ■ Selecting a preset station 52
- ProgramType 53
- CLASSICS 53
- TPFM101.30MHz 53
- ■ Playback screen 54
- ■ Browse screen 55
- Connected 56
- (simple play) 58
- ■ Repeat/shuffle settings 59
- Media sharing setup 63
- Playback of PC music contents 63
- TV screen 66
- ( ) appears 68
- Preparing Zone2 70
- ■ Using an external amplifier 71
- (remote connection) 71
- Controlling Zone2 72
- Pr ess PARTY 73
- AudioDecoder 74
- ToneControl 75
- ■ Tone Control (Tone Control) 76
- ■ Adaptive DRC (Adaptive DRC) 76
- ■ Volume Trim (Volume Trim) 77
- ■ Enhancer (Enhancer) 77
- ■ Video Mode (Video Mode) 77
- ■ FM Mode (FM Mode) 77
- CONFIGURATIONS 78
- ■ Rename/Icon Select 79
- ■ Audio In 79
- ■ Decoder Mode 79
- ■ Volume Interlock 80
- ■ Video Out 80
- ■ DMC Control 80
- Scene menu items 81
- ■ Settings for sound programs 83
- ■ Settings for decoders 84
- Setup menu items 86
- ■ Power Amp Assign 88
- ■ Configuration 88
- ■ Distance 90
- ■ Parametric EQ 90
- ■ Test Tone 90
- ■ Lipsync 91
- ■ Dynamic Range 91
- ■ Max Volume 91
- ■ Initial Volume 92
- ■ Adaptive DSP Level 92
- ■ Video Mode 92
- ■ HDMI Control 93
- ■ Audio Output 94
- ■ Standby Through 94
- ■ IP Address 95
- ■ Network Standby 95
- ■ MAC Address Filter 95
- ■ Network Name 96
- ■ Main Zone Set 96
- ■ Zone2 Set 97
- ■ Party Mode Set 97
- ■ Display Set 97
- ■ Trigger Output 98
- ■ Memory Guard 99
- ■ Auto Power Down 99
- ■ ECO Mode 99
- Language 100
- Types of information 101
- SPIMP.8MIN 102
- TUFM50/AM9 103
- TVFORMATNTSC 103
- MON.CHKYES 103
- INITCANCEL 103
- UPDATEUSB 104
- VERSIONxx.xx 104
- ■ TV operations 105
- ■ Playback device operations 106
- (learning) 107
- Numeric keys 108
- Input selection keys 108
- Press CODE SET 109
- Cursor keys 110
- APPENDIX 111
- First, check the following: 112
- FM/AM radio 115
- USB and network 115
- Ideal speaker layout 118
- ■ Audio decoding format 119
- ■ Others 120
- Yamaha technologies 121
- ■ Video conversion table 122
- Information on HDMI 123
- HDMI signal compatibility 124
- (U.S.A. model) 125
- Trademarks 126
- Specifications 127
- Compatible Decoding Formats 128
- Audio Section 128
- Video Section 128
- FM Section 129
- AM section 129
- Numerics 130
- APPENDIX ➤ Index En 131 131
- APPENDIX ➤ Index En 132 132
- APPENDIX ➤ Index En 133 133
- APPENDIX ➤ Index En 134 134
- APPENDIX ➤ Index En 135 135
- Français 138
- AV Receiver 139
- ■ For U.K. customers 140
- Equipment and Used Batteries 142
- Supplement for Web Control 143
- ■ Top menu screen 144
- ■ Control screen 144
- ■ Settings screen 145
- ■ About FLAC codec Library 146
- ■ About libexpat 146
- Blu-ray Disc 155
- DVD Recorder 156
- Satellite 156
- ■ About The Independent JPEG 160
- Group’s JPEG software 160
- ■ About JsonCpp 160
- ■ About Ogg/Vorbis 160
- ■ About RC4 Algorithm 161
- ■ About zlib Library 161
Related products and manuals for AV receivers Yamaha RX-A820
AV receivers Yamaha RX-V750 Manual
(92 pages)
(92 pages)
AV receivers Yamaha RX-V2065 Owner's Manual
(114 pages)
(114 pages)
AV receivers Yamaha DSP-Z11 Manual
(150 pages)
(150 pages)
AV receivers Yamaha RX-V440 Owner's Manual
(66 pages)
(66 pages)
© 2020, manymanuals.com. All rights reserved. | 0.468 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals