Yamaha QL5 Owner's Manual Page 35
- Page / 59
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Setting the input channels
Owner’s Manual
35
Patching the input port
1. Press the I/O DEVICE button in the touch screen.
2. Press the DANTE PATCH tab in
the upper part of the I/O
DEVICE screen.
3. Press the DANTE INPUT PATCH
button in the I/O DEVICE
screen.
4. Press the AUTO SETUP button.
5. When a confirmation dialog appears, press the
OK button.
6. Press the X symbol to close the screen.
Patching the mixer output to the I/O
device
1. Press the I/O DEVICE button
and then the Rio tab in the
touch screen.
2. Press the OUTPUT display of the I/O device that
is the output destination.
3. Press the OUTPUT1 button in the
OUTPUT PATCH screen.
4. In PORT SELECT, select the output channels you
want to output to the rack.
5. Press the CLOSE button.
6. In the same way, set OUTPUT 2 and subsequent
outputs, if necessary.
Setting the input channels
Phantom power on/off
1. Press the [SEL] key for the channel that you want
to adjust in the Channel Strip section.
2. Press the GAIN knob in the SELECTED CHANNEL
VIEW screen.
3. For the microphone to be used, press the +48V
button in the GAIN/PATCH popup window, if
necessary.
NOTE
• The phantom power master switch on the I/O device must
be turned on first.
• Make sure that phantom power is turned OFF unless it is
needed.
• When turning phantom power on, pay careful attention to
the following to prevent damage or noise in the mixing
console or connected equipment.
- Turn the button off if equipment that does not use
phantom power is connected to INPUT jacks.
- Do not connect or disconnect a cable to or from INPUT
jacks while the button is on.
- Set all digital mixing console output controls to minimum
when turning phantom power ON or OFF.
Adjusting the analog gain
1.
Press the [SEL] key for the channel that you want
to adjust in the Channel Strip section.
2. Press the [CUE] key of the same channel.
3. While checking the sound level through the
headphones and meters, adjust the channel
[GAIN] knob of the Selected Channel section.
NOTE
Adjust the gain level as high as possible without allowing
the OVER segment of the channel strip level meter to light
at the highest input level.
GAIN knob
➩
- Owner’s Manual 1
- Contents 2
- IMPORTANT SAFETY 3
- INSTRUCTIONS 3
- FCC INFORMATION (U.S.A.) 4
- WARNING 5
- CAUTION 5
- Connections 6
- Maintenance 6
- Handling caution 6
- Backup battery 6
- Information 7
- Introduction 8
- An overview of the 9
- QL series 9
- About the models 10
- Controls and functions 11
- Channel Strip section 12
- SENDS ON FADER section 12
- Display section 13
- Selected Channel section 13
- Master section 14
- USER DEFINED KEYS section 14
- FADER BANK section 14
- Front panel 15
- Rear panel 16
- ” iPad application 17
- Touch screen 18
- On-screen user interface 19
- Owner’s Manual 19
- Viewing the touch screen 20
- Using the tool buttons 21
- Basic operation of 22
- Assigning a name 23
- Using libraries 24
- 1 EQ field 25
- 2 Dynamics 1/2 field 25
- 1 RACK button 25
- 2 RACK container 25
- 3. Press the LIBRARY button 26
- 5. Press the RECALL button 26
- Initializing settings 28
- Copying and pasting 28
- Comparing two sets of 29
- Connection 30
- 1 2 3 4 5 6 7 8 31
- Audio input/output 32
- Installing an optional card 33
- Quick Guide 34
- Setting the input channels 35
- Sending an input channel 36
- Applying EQ/dynamics 36
- Setting the output channels 37
- Using GEQ 37
- Using Automixer 38
- Applying effects 38
- Changing the patch settings 40
- Grouping and linking 41
- Using talkback 41
- Routing the oscillator to an 42
- Using scene memories 42
- Recording and playing audio 43
- Saving and loading the unit 44
- Other functions 45
- Initializing the unit to 46
- Adjusting the faders 46
- (Calibration function) 46
- 10. Press the EXIT button 47
- Troubleshooting 48
- (sold separately) 50
- General specifications 51
- Dimensional Diagrams 52
- Block Diagram 55
- CUE / STEREO MONITOR 56
- CUE / SURROUND MONITOR 56
- Level Diagram 57
Related products and manuals for Audio mixers Yamaha QL5
Audio mixers Yamaha V3 Manual
(312 pages)
(312 pages)
Audio mixers Yamaha MG16/6FX Owner's Manual
(32 pages)
(32 pages)
Audio mixers Yamaha V4.5 User's Guide
(55 pages)
(55 pages)
Audio mixers Yamaha MA2030 Datasheet
(2 pages)
(2 pages)
Audio mixers Yamaha EMX66M Owner's Manual
(31 pages)
(31 pages)
Audio mixers Yamaha MG102Cc Owner's Manual
(21 pages)
(21 pages)
Audio mixers Yamaha MG16 Owner's Manual
(32 pages)
(32 pages)
Audio mixers Yamaha AG03 Specifications
(2 pages)
(2 pages)
Audio mixers Yamaha MW10c Owner's Manual
(31 pages)
(31 pages)
Audio mixers Yamaha mc-1202 User Manual
(18 pages)
(18 pages)
Audio mixers Yamaha M2500 User Manual
(50 pages)
(50 pages)
Audio mixers Yamaha MG20XU User Manual
(2 pages)
(2 pages)
Audio mixers Yamaha M7CL V1 Owner's Manual
(282 pages)
(282 pages)
Audio mixers Yamaha PM5D/PM5D-RH Owner's Manual
(367 pages)
(367 pages)
Audio mixers Yamaha 01X User Manual
(156 pages)
(156 pages)
Audio mixers Yamaha AG06 Specifications
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 1.132 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals