Yamaha DTX582K Manual download pdf (Page 2)

 Drum trigger module

1. Secure the module holder to the bottom of the drum trigger

module using the module holder screws.

2. Push the module holder into the holder clamp and tighten the

clamp bolt to secure it in place.

 Cymbal pads

1. Using the tuning key, loosen the stopper’s key bolt.

2. Remove the wing nut, the two felt pads, and the bolt cover

from the cymbal holder.

3. Place the stopper on the cymbal holder.

* If the key bolt was not sufficiently loosened in Step 1

above, it may not be possible to pass the stopper over the

cymbal holder’s shaft. In such a case, loosen the key bolt

as much as possible without removing it.

4. Replace the bolt cover.

* Turn the bolt cover to tighten it onto the threaded section

and firmly secure it in place.

5. With the stopper making full contact with the bottom surface

of the bolt cover as shown below, tighten the stopper’s key

bolt using the tuning key.

6. Place one of the felt pads removed in Step 2 on the cymbal

holder.

7. Mount the pad on the cymbal stand. Lower the pad into place

with the cymbal holder’s shaft passing through the central

hole. When mounted, the stopper’s pin should rest inside the

pad’s smaller hole.

* If you were to play your cymbal pad without the stopper’s

pin positioned well inside the smaller hole, the pad could

rotate, causing the pin to be pulled out. It is very important,

therefore, to ensure that the stopper is secured as shown

in Step 5 above.

8. Assemble the felt pad that came with the cymbal pad.

* The second felt pad removed from the cymbal holder in

Step 2 above is not required for assembly.

9. Tighten the wing nut to secure the pad to the cymbal holder.

A cymbal pad’s built-in sensor is located close to the Yamaha

logo found on the top surface. In order to achieve the best per-

formance from your pad, position it such that the area around

the logo can be easily struck. (See the figure above.)

PCY135

Drum trigger

module

PCY135

Module holder screws

* Two screws for DTX502 /

Four screws for DTX700

Module holder

Drum trigger module

(rear side)

Front side

Clamp bolt

Drum trigger module

module holder

Insert

Holder clamp

Key bolt

Tuning key

Stopper

Cymbal holder

Felt pads

Bolt cover

Wing nut

Cymbal holder

Stopper

Bolt cover

Threaded section

Cymbal holder

Stopper

Bolt cover

Full contact

Cymbal pad

Felt pad that came

with cymbal

Cymbal holder

Felt pad

Bolt cover

Cymbal pad

Stopper

Wing nut

Stopper’s pin

Smaller hole

Assembling the drum trigger module and cymbal pads

1. If a drum mat (sold separately) is not available, lay a sheet of

cardboard on the floor to protect it from being scratched.

2. Loosen the hi-hat stand’s wing bolt a.

3. Open up the three legs as shown below and then retighten

the wing bolt a to lock them in place.

4. Insert the footboard stabilizer rods into the frame holes as

shown below.

5. As shown on the right, loosen the hi-hat clutch’s wing bolt b

and remove the hi-hat clutch.

* The hi-hat clutch is not required when assembling the elec-

tronic drum kit in the standard fashion described in this

manual. Instead, the hi-hat clutch that came with the

RHH135 Real Hi-Hat Pad will be used.

6. Remove the hi-hat shaft from the upper tube .

7. Insert the hi-hat shaft from Step 6 as far as it will go into

the lower tube and screw in the tip.

8. Insert the upper tube over the hi-hat shaft and tighten

the wing bolt c to secure it in place with the cymbal support

plate approximately half way between the top of the lower

tube and the top of the hi-hat shaft .

9. Remove the felt pad attached above the cymbal support

plate. It is not required when assembling the electronic drum

kit in the standard fashion described in this manual.

10. Assemble the RHH135 Real Hi-hat Pad.

* For detailed instructions, refer to the Setting Up section

in the RHH135 Owner’s Manual.

Footboard

stabilizer rod

Wing bolt a

Footboard

stabilizer rod

Felt washer

Hi-hat clutch

Cymbal

support

plate

Cymbal

support plate

Assembling the hi-hat stand

1. If a drum mat (sold separately) is not available, lay a sheet of cardboard on the floor to protect it from being

scratched.

2. Remove the two wing bolts, spring washers, and flat washers from the kick pad frame, and line up each set

nearby in the order of removal.

3. Join the base section to the frame as shown on the right, and then secure it in place by assembling the wing

bolts, spring washers, and flat washers removed in the previous step from the base side.

Frame

Base

Flat washerSpring washer

Wing bolt

Assembling the kick pad

Arrange the hi-hat stand and the kick pad as shown in Example of standard assembly on the other side of this sheet.

• Lay a drum mat (sold separately) on the floor underneath the hi-hat stand and the kick pad. Alternatively, you can place cardboard from the drum kit packaging or the like

on the floor to prevent it from being scratched.

• Ensure that you do not lower the electronic drum rack’s center strut too much as doing so may cause it to come into contact with the kick pad.

Connect the pads to the drum trigger module.

As described below, connect the output of each pad to the corresponding trigger input jack on the drum trigger module.

Connect the drum trigger module to a power supply.

Setting up the drum trigger module.

NOTICE

1. Plug the straight ends of the nine-channel snake cable into the trigger input jacks on the back of the

drum trigger module.

• When using the standard setup, the stickers on each of the snake cable’s plugs will indicate the name

of the corresponding pad.

2. Plug the L-shaped ends of the nine-channel snake cable into the corresponding pads.

3. In the case of snare and tom pads, wrap the cables around the cable clips to prevent them from being

pulled out.

Excessive bending can damage pad cables. Ensure, therefore, that these cables

are not bent at an extreme angle when wrapped around the clips.

Pads DTX502 jack names DTX700 jack names

SNARE q SNARE q SNARE

TOM1 w TOM1/!0 w TOM1

TOM2 e TOM2/!1 e TOM2

TOM3 r TOM3/!2 r TOM3

RIDE t RIDE t RIDE

CRASH y CRASH y CRASH1

KICK u KICK/io KICK/!0

HI HAT o HI HAT i HI HAT

HH CON HI-HAT CONTROL HI-HAT CONTROL

NOTICE

RIDE

TOM3

TOM2

KICK

TOM1

SNARE

CRASH

HI HAT HH CON

Locations of pad jacks

1. Plug the power adaptor’s DC cord into the connector. Hook the power adaptor’s DC cord around

the cord clip to secure it in place.

2. Using the cable bands, secure the cables to the electronic drum rack at the positions circled in the figure

on the right. ( )

3. Plug the adaptor’s AC cord into a domestic wall socket.

Drum trigger module’s rear panel

Cord clip

connector

* The illustration shows the DTX502 drum trigger module.

[For DTX582K Owners]

Select the “DTX582K” trigger setup on the DTX502 drum trigger module. (For details on the trigger

setup procedure, see “Trigger Setup” from the DTX502 Owner’s Manual.)

If “DTX582K” is not displayed on the selection screen, select the “DTX562K” trigger setup, and then

make the following adjustment.

• Kick pad output (LEVEL) adjustment:

Adjust the trigger output to your desired setting by using the KP100 kick pad’s level adjustment

knob. For details, see “Adjusting the Output Level” from the KP100 Owner’s Manual.

[For DTX720K Owners]

Select the “DTX720K” trigger setup on the DTX700 drum trigger module. (For details on the trigger

setup procedure, see “Selecting a Sensitivity for the Entire Kit” from the DTX700 Owner’s Manual.)

If “DTX720K” is not displayed on the selection screen, please upgrade your DTX700’s firmware ver-

sion. Visit the following web page for information on the latest DTX700 firmware version and to

download firmware version upgrades.

http://download.yamaha.com/

If you would prefer not to upgrade your firmware version, select the “DTX700K” trigger setup, and

then make the following adjustment.

• Kick pad output (LEVEL) adjustment:

Adjust the trigger output to your desired setting by using the KP100 kick pad’s level adjustment

knob. For details, see “Adjusting the Output Level” from the KP100 Owner’s Manual.

Your electronic drum kit is now ready. * For instructions on turning on the drum trigger module, producing sounds, and other subsequent steps,

please refer to the Owner’s Manual that came with the module.

1 2

Comments to this Manuals

No comments

Yamaha DTX582K Manual Page 2

Comments to this Manuals

Related products and manuals for Unknown Yamaha DTX582K