Yamaha A-S2100 Owner's Manual

© 2014 Ya maha CorporationIntegrated AmplifierOWNER’S MANUALABPrinted in Malaysia VAA8480

10 EnControls and functions Rear panel1 BAL (balanced) input jacksOne set of balanced input jacks is provided.Set the ATTENUATOR selector and PHASE s

11 EnA AUTO POWER STANDBY switchON: The unit enters STANDBY mode automatically if not operated for 8 hours.OFF: The unit does not enter STANDBY mode a

12 EnControls and functions Remote control1 Infrared signal transmitterOutputs infrared control signals.2 p AMP keyTurns this unit ON or switches it

13 En5 p CD keyTurns the Yamaha CD player ON or switches it to STANDBY mode.6 OPEN/CLOSE keyOpens/closes the disc tray of the Yamaha CD player. Refer

14 EnControls and functions Installing batteries in the remote control1 Remove the battery compartment cover.2 Insert the two batteries (AAA, R03, UM

ConnectionsIn this section, you will make connections between A-S2100, speakers,and source components.

16 EnConnections• Do not let the bare speaker wires touch each other or do not let them touch any metal part of this unit. This could damage this unit

17 En• Because the power amplifier of A-S2100 is of the floating balanced type, the following types of connections are not possible.– Connecting with

18 EnConnections Connecting the speakers1 Remove approximately 10 mm of insulation from the end of each speaker cable and twist the exposed wires of

19 En Bi-wire connectionThe bi-wire connection separates the woofer from the combined midrange and tweeter section. A bi-wire compatible speaker has

2 EnA Living Tradition in SoundA piano comes into this world through the perfect synergy of advanced technical skill and artistry. Such a piano can cr

20 EnConnections Connecting to the BAL jacksConnect your CD player or network player with the XLR balanced output jacks. Set the ATTENUATOR selector

21 En Operating this unit from another roomIf you connect an infrared receiver and transmitter to the REMOTE IN/OUT jacks of this unit, you can opera

22 EnConnections Connecting a component supporting the trigger function such as a Yamaha AV receiverThe operations of this unit can be controlled in

SpecificationsIn this section, you will find technical specifications for A-S2100.

24 EnSpecificationsPOWER SECTION• Rated Output Power[U.S.A, Canada, Taiwan, China, Korea, Australia, U.K. and Europe models] (8 , 20 Hz to 20 kHz, 0

25 En Block diagram CD TUNER LINE1 LINE2 LINE2 OUT PHONO INPUT SELECTOR ATT.UINT1 PRE OUT MAIN INMM//MCFLOATING BALANCESPEAKER DRIVERMOSFETL CHFLOATI

26 EnSpecifications Tone control characteristics Total harmonic distortion10 20 30 50 100 200 300 500 1kFrequency (Hz)Response (dB)2k 3k 5k 10k 20k

27 En Total harmonic distortion (PHONO)100µ 200µ 500µ 1m 2m 5m 10m 20mGenerator Level (Vrms)50m 100m 200m 500m 1 220Hz 1kHz 20kHz1052310.50.20.30.020

28 EnTroubleshootingRefer to the chart below if this unit does not function properly. If the problem you are experiencing is not listed below or if th

29 EnProblem Cause RemedySee pageThe sound from the component connected to the BAL jack is degraded.The sound level is higher than the maximum input l

3 EnNP-S2000Soavo-1NS-10MA-S3000CD-S3000NS-20CA-1000NS-690B-1PX-2C-2NS-1000MA-1B-6B-2xMX-10000CX-10000Excellence in Audio AchievementFirst HiFi System

© 2014 Ya maha CorporationIntegrated AmplifierOWNER’S MANUALABPrinted in Malaysia VAA8480

4 En◆ Full floating and balanced circuit design achieves the full potential of analogue amplificationAn entirely new floating and balanced power ampli

5 EnControls andfunctionsIn this chapter, you will learn the controls and functions of A-S2100.

CONTROLS AND FUNCTIONS6 EnControls and functions Front panel (pages 6 to 9)1 STANDBY/ON, OFF switchTurns on or off this unit.STANDBY/ON (upper positi

7 En4 TRIM selectorAdjusts the volume level when headphones are plugged in to avoid sudden changes in volume.Choices: –6 dB, 0 dB, +6 dB, +12 dB5 SPEA

8 EnControls and functions Front panel (pages 6 to 9)A Remote control sensorReceives signals from the remote control.B INPUT selector/indicatorSelect

9 EnC PHONO switchSelects the type of cartridge of the turntable connected to the PHONO jacks on the rear panel.MM: Choose this setting if the connect