Yamaha RM1x Service Manual download pdf (Page 27)

RM1x

Display Of Test Results

Test End

After displaying the test result when the check

to the [TAP] switch end and the test will be

finished.

After Pressing the [F4] to exit the test, press the

[+1] switch to proceed with the next test and

then the [ENTER] switch to execute the next test.

Refer to

“

B PROCEEDING THROUGH THE

TESTS

”

if the

“

”

occurs while testing.

C-6 ENCODER 1

[

]

TEST

Confirm the Encoder corresponding to the

[F1]

switch are working properly from the left side.

When you rotate the Encoder clockwise according

to the LCD display, the value at the right of the

LCD simply increases from 0 to 30. When you

rotate the Encoder counterclockwise, the value

at the right of the LCD simply increases from 0

to 30. After that, confirm that the OK appears on

the LCD.

(where xx= current ENCODER 1 value)

Display Of Test Results

NG Not appearing

Test End

After displaying the test result and the test will

be finished.

After Pressing the [F4] to exit the test, press the

[+1] switch to proceed with the next test and

then the [ENTER] switch to execute the next test.

Refer to

“

B PROCEEDING THROUGH THE

TESTS

”

if the

“

”

occurs while testing.

C-7 ENCODER 2

[

]

TEST

C-8 ENCODER 3

[

]

TEST

C-9 ENCODER 4

[

]

TEST

These tests can be performed in the same manner

as the test C-6,

“

ENCODER 1

[F2]

TEST

”

C-10 KNOB 1 (BEAT STRETCH) TEST

(where xxx= current KNOB 1 value)

According to the target value displayed on the

LCD, slowly rotate the KNOB 1.

Check that the value changes from 64 to 128

then to 00 and back to 64 (in other words, center

to top then to bottom and back to center). After

that, confirm that the

“

”

appears on the LCD.

(where xxx= current KNOB 1 value and

yyy= target value)

Display Of Test Results

NG Not appearing

When the value of the display passes 64 after

64-128-00 and passes 64 , OK is displayed.

Test End

After displaying the test result and the test will

be finished.

After Pressing the [F4] to exit the test, press the

[+1] switch to proceed with the next test and

then the [ENTER] switch to execute the next test

Refer to

“

B PROCEEDING THROUGH THE

TESTS

”

if the

“

”

occurs while testing.

C-11 KNOB 2 (CLOCK SHIFT) TEST

C-12 KNOB 3 (GATE TIME) TEST

C-13 KNOB 4 (VELOCITY) TEST

C-14 KNOB 5 (CUTOFF) TEST

C-15 KNOB 6 (RESONANCE) TEST

C-16 KNOB 7 (EG DECAY) TEST

C-17 KNOB 8 (PITCH BEND) TEST

These tests can be performed in the same

manner as the test

C-10

“

KNOB 1 (BEAT) TEST

”

C-18 FOOT SW TEST

Connect a foot switch and press it on and off.

Check that the display on the LCD changes

from off to on then back to off and verify that to

the

“

”

result is displayed.

05: Panel Switch

Push [MODE ] NG

10: Knob 1

xxx 64

10: Knob 1

xxx yyy

06: Encoder 1

RIGHT 00

10: Knob1

064 064 OK

06: Encoder1

RIGHT xx

06: Encoder1

LEFT xx

06: Encoder1

LEFT 00

18: FOOT SW

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 53 54

Comments to this Manuals

No comments

Yamaha RM1x Service Manual Page 27

Comments to this Manuals

Related products and manuals for Sequencer Yamaha RM1x