Yamaha DTX520K Owner's Manual download pdf (Page 1)

DTX540K/DTX520K Assembly Manual

This pamphlet describes the standard procedure for DTX540K/DTX520K assembly.

After assembling the parts and connecting the cords as shown below, you will be ready to turn on the drum trigger module.

• For assembly, you will require four individual packages – an RS500

Rack System, a DTP520C Pad Set, a DTP700P Pad Set*, and a

DTX500 Drum Trigger Module. (*: The DTX520K uses a DTP520P

Pad Set instead.)

• This pamphlet describes how to attach the pads and drum trigger

module to the RS500 Rack System. Before carrying out the proce-

dures described below, ensure that you have correctly assembled

the rack system as described in its assembly manual.

• Although this pamphlet uses illustrations of the DTX540K, the

assembly procedures described also apply to the DTX520K.

Before starting assembly, lay a drum mat (sold separately) on the floor.

Alternatively, before setting up the HH65 Hi-hat Controller and KP65

Kick Pad, you can place the packages' cardboard boxes on the floor to

protect it from damage.

Before using, please read this assembly manual, and use this product in a safe and proper manner.

* Please keep this manual in a safe place for future reference.

* Make sure to read the Assembly Manual of the Rack System and the Owner’s Manual of the Pad.

NOTICE

• Make sure you hold onto the plug, not the cable, when connecting or disconnecting the cable. Also,

never place any heavy or sharp objects on the cable. Applying excessive force to the cable may

result in damage to the cable, such as the wires being severed, etc.

• Do not step on or place heavy objects on the product. It may result in damage.

• Do not use or keep the product in places with extremely high temperature (places in direct sunlight,

close to a heater, in a closed car, etc.) or high humidity (bathroom, outside on a rainy day, etc.).

Doing so may result in deformation, discoloration, damage or deterioration.

• When cleaning the product, do not use benzine, thinner or alcohol as it may result in discoloration or

deformation. Please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the

product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has

been wrung out thoroughly to remove any remaining detergent. Also pay close attention so as not to

let the water and detergent come into contact with the cushions used in the product; doing so may

result in deterioration.

* Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at

any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.

PRECAUTIONS

Example of standard DTX540K assembly

PCY100

(Cymbal Pad)

XP70

(Tom Pad)

XP70

(Tom Pad)

KP65

(Kick Pad)

XP80

(Snare Pad)

HH65

(Hi-hat Controller)

DTX500 Drum

Trigger Module

PCY100

(Hi-hat Pad)

RS500

(Rack System)

PCY135

(Cymbal Pad)

IMPORTANT

NOTICE

If this symbol is ignored and the equipment is used improperly, fatal

injury to persons or serious damage could occur.

• Do not let small children assemble or set up this product by themselves, or they may be injured.

Always assemble this product with adult supervision.

• Be careful with the edges of the Cymbal Holders and the Tom Holders. The sharp holder ends

may result in injury.

• Be careful with the edges of the spurs attached to the Kick Pad and foot pedal. The sharp ends

may result in injury.

• If this product is used with a Rack System or Cymbal Stand, make sure all bolts are tightened

firmly. Also, when adjusting the height or angle, do not suddenly loosen the bolts. Loose bolts may

result in the rack overturning or parts dropping, causing injury.

• Always set the product on a flat and solid surface. Placement on a sloping, unstable surface or on

steps may result in the product being unstable and subject to overturning.

• When setting up the product, please pay close attention to the handling and setting of cables.

Carelessly placed cables may cause the user and others to trip and fall.

• Do not alter the product. Doing so may result in injury or damage/deterioration to the product.

• Do not sit or step on the rack. The rack may overturn or be damaged, resulting in injury.

If this symbol is ignored and the equipment is used improperly,

there is a danger or injury to persons handling the equipment, and

material damage could occur.

• Watch your fingers when adjusting clamps. They may become pinched, resulting in injury.

• Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your

fingers.

• Do not put your hands or feet under the foot pedal or foot switch. They may be pinched, resulting

in injury.

• Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums

may drop, causing injury.

Digital Musical Instruments DivisionDigital Musical Instruments Division

WW60810 110PO***.*01C0

WARNING

CAUTION

Assemble the RS500 Rack System.

For details, refer to the assembly manual that came with the rack system.

Check the contents of each package.

Mount the pads and the drum trigger module on the rack system.

As described below, mount the pads and the trigger module on the rack system, and then position the kick pad and the hi-hat controller.

Package 1: DTP520C Package 2: DTP700P (for DTX540K)

 PCY135

Cymbal Pad (x1)

 PCY100

Cymbal Pad (x2)

 HH65

Hi-hat Controller (x1)

 Hi-hat holder (x1)  Stoppers for the

PCY100 and PCY135

(x3)

 Tuning key (x1)

 9-channel snake cable (x1)

 PCY100, PCY135, and PCY155 Owner’s Manual (x1)

 HH65 Owner’s Manual (x1)

 Assembly Manual (this pamphlet)

 XP80

Snare Pad (x1)

 XP70

Tom Pad (x3)

 KP65

Kick Pad (x1)

 Clamp bolts (x4)

 XP70 and XP80 Owner’s Manual (x1)

 KP65 Owner’s Manual (x1)

Package 3: DTX500

 DTX500 Owner’s Manual (x1)

 DTX500 Drum Trigger

Module (x1)

 AC power adaptor*

(x1)

 Module stand (x1)

 Module stand

fastening screws (x2)

 Felt for the

PCY135 (x1)

 Felts for the

PCY100 (x2)

 Cable bands (x10)

Package 2: DTP520P (for DTX520K)

 XP80

Snare Pad (x1)

 TP65

Tom Pad (x3)

 KP65

Kick Pad (x1)

 Clamp bolts (x4)

 XP70 and XP80 Owner’s Manual (x1)

 KP65 Owner’s Manual (x1)

 TP65, TP65S, TP100, and TP120SD

Owner’s Manual (x1)

* May not be included depending on your particular area.

Please check with your Yamaha dealer.

Mounting the hi-hat holder

1. Remove the drum trigger module clamp a from the left of the rack, together with

the left leg b.

2. Assemble the holder clamp for the hi-hat holder ensuring that it is oriented as

shown in the figure, and then reassemble the left leg b and the drum trigger mod-

ule clamp a.

Drum trigger

module clamp

Left leg b

Drum trigger

module clamp a

Left leg b

Holder clamp

Hi-hat holder

Continued on other side

1 2

Summary of Contents

Page 1 - PRECAUTIONS

DTX540K/DTX520K Assembly ManualThis pamphlet describes the standard procedure for DTX540K/DTX520K assembly. After assembling the parts and connecting

Page 2 -  Mounting the tom pad

Mounting snare and tom pads Mounting the snare pad1. Attach the clamp bolt to the snare pad and provi-sionally tighten (by 5 or 6 turns).2. Mount the