Yamaha YDP-184 Owner's Manual download pdf (Page 100)

100

YDP-184 Owner’s Manual

Troubleshooting

When a message is displayed, refer to the “Message List” (page 98) for troubleshooting aid.

Problem Possible Cause and Solution

The instrument does not turn

on.

The instrument has not been plugged in properly. Securely insert the female plug into the socket on the

instrument, and the male plug into a proper AC outlet (page 14).

A click or pop is heard when

the power is turned on or off.

This is normal when electrical current is being applied to the instrument.

The power is automatically

turned off.

This is normal and due to the Auto Power Off function. If necessary, set the parameter of the Auto Power Off

function (page 90).

The message “USB device

overcurrent error” is shown

and the USB device does not

respond.

Communication with the USB device has been shut down because of the overcurrent to the USB device.

Disconnect the device from the USB [TO DEVICE] terminal, then turn on the power of the instrument.

Noise is heard from the

speakers or headphones.

The noise may be due to interference caused by the use of a mobile phone in close proximity to the instrument.

Turn off the mobile phone, or use it further away from the instrument.

Noise is heard from the

instrument’s speakers or

headphones when using the

instrument with the

application on iPhone/iPad.

When you use the instrument along with the application on your iPhone/iPad, we recommend that you set that

device’s “Airplane Mode” to “ON” and then the Wi-Fi setting to “ON” on your iPhone/iPad in order to avoid noise

caused by communication.

The overall volume is low, or

no sound is heard.

The Master Volume is set too low; set it to an appropriate level using the [MASTER VOLUME] slider (page 17).

The volume level for the keyboard performance is set too low. Adjust the volume balance to increase the

keyboard volume via the “Song” menu display: “Volume”  “Song - Keyboard” (page 45).

Headphones are connected when the Speaker setting is “Normal” (page 90). Disconnect the headphone plug.

The Speaker setting is “Off.” Set the Speaker to “Normal” via the “System” menu display: “Utility”  “Speaker”

(page 90).

Local Control is “Off.” Set Local Control “On” via the “System” menu display: “MIDI”  “Local Control” (page 89).

“Expression” is assigned to the right pedal. Assign any function other than “Expression” to the pedal (page 80)

via the “Voice” menu display: “Pedal Assign”  “Right” (page 80).

The speakers do not switch

off when a pair of

headphones is connected to

the [PHONES] jack.

The Speaker setting is “On.” Set the speaker setting to “Normal” via the “System” menu display: “Utility” 

“Speaker” (page 90).

Pedals do not function. The pedal cord may not be securely connected to the [PEDAL] jack. Be sure to insert the pedal cord all the way

until the metal part of the cord plug disappears from view (page 104).

The keyboard volume is

lower than the Song playback

volume.

The volume level for the keyboard performance is set too low. Adjust the volume balance to increase the

keyboard volume via the “Song” menu display: “Volume”  “Song - Keyboard” (page 45).

The buttons do not respond. While you are using a function, some buttons not used for the function are disabled. If the Song is playing, stop

playback. Otherwise, press the [EXIT] button to return to the Voice or Song display, Then, perform the desired

operation.

Higher or lower notes do not

sound correctly when the

transpose or octave setting is

made.

This instrument can cover the range of C -2 – G8 when you set the transposition or octave. If notes lower than C

-2 are played, the sound is moved one octave higher. If notes higher than G8 are played, the sound is moved

one octave lower.

Performance in Dual/Split/

Duo mode is not recorded, or

part data is lost

unexpectedly.

Switching to Dual/Split/Duo mode in the middle of the Song is not recorded. Also, the recording part for the Voice

2 (Dual mode) or the left Voice (Split/Duo mode) is automatically assigned (page 52). If the assigned part

already has data, the data will be overwritten and deleted when you record.

Depending on the selected

Voice, the keyboard sound in

Duo mode may be output

from only one speaker.

This is because the default pan setting differs depending on the Voice.

Change the settings from the “Voice” menu  “Voice Edit”  “Voice name”  “Pan” (page 79).

The Song title is not correct. If the song cannot be read, you may need to change the character for the Song name. For information about the

character types available for the Song name, refer to “Character List” (page 91).

Menu display cannot be

called up.

When Song is being played back, menu display other than “Voice” menu and “Song” menu will not appear. Stop

the Song by pressing the [R/K] (Play/Pause) button. Also, in the recording ready mode, only “Recording” menu

display will appear.

1 2 ... 95 96 97 98 99 100 101 102 103 104 105 ... 109 110

Comments to this Manuals

No comments

Yamaha YDP-184 Owner's Manual Page 100

Comments to this Manuals

Related products and manuals for Digital pianos Yamaha YDP-184