Yamaha S08 Manual download pdf (Page 68)

68

Basics Section Quick Guide Reference Appendix

*1

Changes to velocity curve according to

VelDepth (with Offset set to 64)

VelSnsDpt

Changes to velocity curve according to

VelOffset (with Depth set to 64)

VelSnsOfs

*2

Depending on the selected LFO wave type

and the amplitude modulation depth

setting, noise may result when the

controller is moved. If this happens, reduce

the modulation depth value.

*3

In the value is too high, noise may result. If

this happens, reduce the value.

*4

The Element settings whose Element

Switch is set to “off” can not be changed

and “***” appears in the display.

*5

Wave numbers indicated with an asterisk

(*) and Wave names indicated with an “at”

mark (@) have ﬁxed parameter values

(depending on the sound range). For these

waves, Element editing is limited to the

parameters below. All other parameters

values are replaced by a series of asterisks

in the LCD, indicating that they cannot be

set.

-Element Switch

-Wave Selection

-Note Shift

-Note Limit Low/High

-Velocity Limit Low/High

-Pitch Scale Sensitivity

-Pitch Scale Center Note

*6

Element control according to the note

position on the keyboard

(ex. PEG Rate : Speed of PEG change)

* Negative value is only available for PEG

*7

Element control according to Velocity

(ex. PEG)

* Only positive values are available for the

AEG and Filter settings.

*8

Settings: brk.p (applies the BP parameter

settings in the following PAGES), table

(applies the settings which are preset for

each voice. This setting is effective only

for XG Voices.)

*9

Filter Scaling Settings

By way of example, you could set the

Levels (Offsets) and Break Points (BP1 to

BP4) as follows.

Here, the current Cutoff setting is 64. The

Offsets are -64 at BP1 (set to note E1),

+10 at BP2 (set to note B2), +17 at BP3

(set to note G4) and +60 at BP4 (set to

A5). That is, the Cutoff frequencies at each

Break Point are 0, 74, 81 and 124,

respectively. For other notes, the Cutoff

frequencies will be on the straight line

connecting the two adjacent Break Points.

The Break Point Levels are Offsets used to

increase or decrease the current Cutoff

setting at the speciﬁed notes. Regardless of

the size of these Offsets, the minimum and

maximum Cutoff limits(values of 0 and

127, respectively) cannot be exceeded.

A note set below the BP1 will become the

BP1Level. A note set above BP4 will

become the BP4 Level.

The availability of the FEG Scaling

parameter depends on the Break Point and

Offset settings in the Flt BP/Flt Ofs

PAGES.

*10

When the FltSclSns is set to 0, Filter

Scaling Settings (PAGES 15, 16, 17) will be

ignored (ﬂat). When set to 15, the values

in the Flt Ofs settings will be added at a

rate of 100%.

Received Velocity

(Actual KeyOn speed)

Actual Velocity

for tone generator

Depth=127 (twice)

Depth=64

(normal)

Depth=32

(half)

Depth=0

127

127

64

64

0

64

127

0

127

64

Received

Velocity

(Actual KeyOn speed)

Actual Velocity

for tone generator

Offset=96 (+64)

Offset=127 (+127)

Offset=64 (normal)

Offset=32 (-64)

Depends on

offset

Depends on

offset

Offset=0 (-127)

Basic pitch

Positive value

Higher range

Lower range

Slower speed

Faster speed

+7

+3

-4

Negative value

Large

Velocity

Positive value

Amount of pitch change

Time of PEG change

Slower speed

Faster speed Large

PEGRtVel PEGLvlVel

Small

Small

1234

BP E1 B2 G4 A5

Ofs –64 +10 +17 +60

0

74

81

124

Note

Number

Cutoff

E1

Break

Point

=

Break

Point

B2

=

Break

Point

G4

=

Break

Point

A5

=

1 2 ... 63 64 65 66 67 68 69 70 71 72 73 ... 87 88

Comments to this Manuals

No comments