Yamaha HTR-9063 Quick Start Guide Page 3

  • Download
  • Add to my manuals
  • Print
  • Page
    / 8
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 2
EXTRA SP1
N
E3
SURROUND SURROUND BACK/
SPEAKERS
CENTER
AV 1 AV 2 AV 3 AV 4
HDMI
AV 5 AV 6 AV 7
SINGLE
FRONT
BI-AMP
AV 3
AV 4
FRONT
SURROUND
SUR. BACK
SUBWOOFER
CENTER
MULTI CH INPUT
COMPONENT VIDEO
MONITOR OUT/ZONE OUT
ZONE OUT PRE OUT
ZONE 2
FRONT/
F. PRESENCE
YP
B
P
R
P
B
P
R
YP
B
P
R
C
D
SURROUND
SUR. BACK
CENTER
(REAR)
(FRONT)
SUBWOOFER
1
2
RS-232C
IN
12
2
1
OUT IN OUT
REMOTE
TRIGGER
OUT
+12V 0.1A MAX.
(1 BD/DVD)
ZONE 3
(SINGLE)
ZONE2/ZONE3/
F.PRESENCE
E
X
T
R
A
P
1
N
E
3
A
V
A
A
1
A
V
A
A
2
A
V
A
A
3
A
V
A
A
4
H
D
M
I
A
V
A
A
5
A
V
A
A
6
A
V
A
A
7
A
V
A
A
3
A
V
A
A
4
F
R
O
N
T
S
U
R
R
O
U
N
D
S
U
R
.
B
A
C
K
S
U
B
W
O
O
F
E
R
C
E
N
T
E
R
M
U
L
T
L
L
I
C
H
I
N
P
U
T
C
O
M
P
O
N
E
N
T
V
I
D
E
O
M
O
N
I
T
O
R
O
U
T
/
T
T
Z
/
/
O
N
E
O
U
T
Z
O
N
E
O
U
T
P
R
E
O
U
T
Z
O
N
E
2
F
R
O
N
T
/
TT
F
.
F
F
P
R
E
S
E
N
C
E
Y
P
B
P
R
P
B
P
R
Y
P
B
P
R
C
D
S
U
R
R
O
U
N
D
S
U
R
.
B
A
C
K
C
E
N
T
E
R
(
R
E
A
R
)
S
U
B
(
(
W
O
O
F
)
)
E
)
)
R
2
R
S
-
2
3
2
C
I
N
1
2
2
1
O
U
T
I
N
O
U
T
R
E
M
O
T
E
T
R
I
G
G
E
R
O
U
T
+
1
2
V
0
.
1
A
M
A
X
.
(
1
B
D
/
D
V
D
)
Z
O
N
E
3
(
S
I
N
G
L
E
)
Z
O
N
E
2
/
Z
/
/
O
N
E
3
/
F
.
F
F
P
R
E
S
E
N
C
E
6.1
7.1 7.1
- 3 -
1
1
Connect the speakers
Front speaker
R L
R L
Surround back
speaker
R L
Surround
speaker
Subwoofer
Center speaker
Connecting speakers
When connecting the presence speakers, refer to “Presence speaker
connection” in the Owner’s Manual.
This unit can connect speakers that support Bi-amp connection for front
speakers. Refer to “Bi-amp connection in the Owner’s Manual.
7.1
Connect when using with 7.1-channel speaker layout.
6.1
Connect when using with 6.1-channel speaker layout.
FRO
N
T
-
2
2
3
1
4
4
+
1
Remove approximately 10 mm of insulation from
the ends of the speaker cables, and twist the bare
wires of the cables together  rmly so that they will
not cause short circuits.
2
Loosen the speaker terminals.
3
Insert the bare wire of the speaker cable into the
gap on the side of the terminal.
4
Tighten the terminal.
Connecting the subwoofer
1
Connect the subwoofer input jack to the SUBWOOFER
1 jack on this unit with an audio pin cable.
(
S
IN
GL
E
)
P
RE OUT
CE
NTER
CE
NTER
S
U
R
.
BA
C
KSU
R
R
U
ND
1
2
FR
O
NT
(
R
EA
R
)
S
UBWO
OF
E
R
(
F
R
ONT
)
2
Set the subwoofer volume as follows.
Volume: Set to approximately half volume (or slightly less than half).
Crossover frequency (if available): Set to maximum.
Subwoofer examples
VOLUME
MIN MAX
CROSSOVER/
HIGH CUT
MIN MAX
Caution:
Remove the power cable of this unit from the power outlet before
connecting the speakers.
Generally speaker cables consist of two parallel insulated
cables. One of these cables is a different color, or has a line
running along it, to indicate different polarity. Insert the different
colored (or lined) cable into the “+” (positive, red) terminal
on this unit and the speakers, and the other cable into the “-”
(minus, black) terminal.
Be careful that the core of the speaker cable does not touch
anything or come into contact with the metal areas of this unit.
This may damage this unit or the speakers. If the speaker cables
short circuit, “CHECK SP WIRES!” will appear on the front panel
display when this unit is switched on.
This unit is con gured for 8 Ω speakers at the factory setting.
When connecting 6 Ω speakers, con gure the speaker
impedance setting of this unit to 6 Ω. When this unit is
con gured for 6 Ω speakers, 4 Ω speakers can also be used as
the front speakers. For more information on setting the speaker
impedance, refer to “Changing speaker impedance” in the
Owner’s Manual.
Connecting the banana plug
Tighten the knob, and then insert the banana plug
into the end of the terminal.
Banana plug
F
R
O
N
T
+
Page view 2
1 2 3 4 5 6 7 8

Comments to this Manuals

No comments