Yamaha V3 Owner's Manual

M7CL V3 Editor Owner’s Manual 1 Special Notices •The software and this owner’s manual are the exclu-sive copyrights of Yamaha Corporation.•Copying of

M7CL V3 Editor Owner’s Manual10Undo/Redo FunctionIn M7CL Editor, you can cancel the latest operation (Undo) and also cancel the cancellation of the la

M7CL V3 Editor Owner’s Manual11Window operationsYou can select and open each window from the [Win-dows] menu. For the INPUT CH window and Effect Edi-t

M7CL V3 Editor Owner’s Manual12Synchronizing M7CL EditorWhen M7CL Editor starts up, the parameter settings on the console and the parameter settings i

M7CL V3 Editor Owner’s Manual 13 In the Master window you can synchronize to the M7CL itself, recall scenes, and display the Overview window. To open

M7CL V3 Editor Owner’s Manual14❏ SYNCThis indicates the status of connection and synchronization between M7CL Editor and the M7CL.A [ONLINE]/[OFFLINE]

M7CL V3 Editor Owner’s Manual15❏ Navigation KeysOpens the corresponding window in the Overview window.These are not linked with the navigation key sec

M7CL V3 Editor Owner’s Manual16INPUT CH windowThis window displays the mix parameters of INPUT CH 1–16, 17–32, or 33–48(*). The parameters shown in th

M7CL V3 Editor Owner’s Manual17D Ø (Phase)Inverts the phase of the signal after AD conversion.E HPF (High Pass Filter)Switches the high pass filter on/

M7CL V3 Editor Owner’s Manual18K PAN/TO STEREO MONOThe PAN knob adjusts the panning of the signal that is sent from the INPUT CH to the STEREO bus L/R

M7CL V3 Editor Owner’s Manual19The numbers and alphabetical let-ters at the right of the fader indicate the DCA group and mute groups to which that ch

M7CL V3 Editor Owner’s Manual 2 Overview of M7CL V3 Editor M7CL V3 Editor (hereinafter called “M7CL Editor” in this document) enables you to remotely

M7CL V3 Editor Owner’s Manual20ST IN window ( M7CL-32/M7CL-48 only)In this window you can view and edit the mix parameters of ST IN channels 1–4. The

M7CL V3 Editor Owner’s Manual21G DYN1/DYN2 (Dynamics 1//Dynamics 2)These buttons switch the two dynamics processors on/off. This is the same as the dy

M7CL V3 Editor Owner’s Manual 22 MIX window In this window you can view and edit the parameters of MIX channels 1–16. The parameters shown in the win

M7CL V3 Editor Owner’s Manual 23 E MATRIX SEND These bar graphs indicate the send levels of the signals sent from the MIX channel to MATRIX 1–8 bus.

M7CL V3 Editor Owner’s Manual24L Channel numberIndicates the number of the MIX channel. You can double-click this number to open the Selected Channel

M7CL V3 Editor Owner’s Manual25A MIX/CH/ST IN (Send levels from the MIX/INPUT CH/ST IN to the MATRIX bus)This switches between indicating the sends fr

M7CL V3 Editor Owner’s Manual26STEREO/MONO windowIn this window you can view and edit the parameters of the STEREO and MONO channels. The parameters s

M7CL V3 Editor Owner’s Manual27E BALANCEAdjusts the left/right balance of the STEREO channel.For MONO channels, this control indicates the send level

M7CL V3 Editor Owner’s Manual28DCA windowIn this window you can view and edit the parameters of DCA groups 1–8.You can access this window in the follo

M7CL V3 Editor Owner’s Manual29Here you can set the parameters of the currently selected input channel (INPUT CH 1–48(*), ST IN channels 1–4) or outpu

M7CL V3 Editor Owner’s Manual 3 C Channel Select / Sends On Fader This checkbox enables you to specify whether or not the M7CL console and M7CL Edito

M7CL V3 Editor Owner’s Manual30Unless otherwise specified, the parameters explained below are common to INPUT CH 1–48 and ST IN channels 1–4.❏ CHANNEL

M7CL V3 Editor Owner’s Manual31❏ TO MIX/TO MATRIX SENDA MIX/MATRIX send levelThis adjusts the send level of the signal sent from the input channel to

M7CL V3 Editor Owner’s Manual32C HPF (High Pass Filter)Use the [ON] button at the right to switch the high-pass filter on/off. You can use the knob at

M7CL V3 Editor Owner’s Manual33❏ EQUALIZERA LIBRARYAccesses the INPUT EQ page of the LIBRARY window.B ONSwitches the EQ on/off.C EQ graphIndicates the

M7CL V3 Editor Owner’s Manual34K ATT (Attenuation)Adjusts the amount of attenuation/gain.❏ DYNAMICS1/2You can select one of the following types for ea

M7CL V3 Editor Owner’s Manual35J HOLDSpecifies the time that the gate will remain open after the key-in signal falls below the threshold.K KEY IN SOURC

M7CL V3 Editor Owner’s Manual36G RATIOSpecifies the ratio at which the input signal will be compressed when the key-in signal exceeds the threshold.H K

M7CL V3 Editor Owner’s Manual37H WIDTHSpecifies the width between the threshold level of the compressor (THRESHOLD) and the threshold level of the expa

M7CL V3 Editor Owner’s Manual38❏ INSERT (except for ST IN channels)A ONEnables/disables insert-in/out.B OUT (Insert out)Click this to select the outpu

M7CL V3 Editor Owner’s Manual39C DIRECT OUT PORTClick this to select one of the following output ports as the one used for direct out.D DIRECT OUT POI

M7CL V3 Editor Owner’s Manual 4 ❏ Mixer Setup To open the Mixer Setup dialogbox, choose [Mixer Setup] from the [File] menu. A Mix Bus Setup Here you

M7CL V3 Editor Owner’s Manual40If a MIX channel is selected❏ CHANNEL SELECT (Channel selection)A SELECT (Channel selection)Except for the fact that yo

M7CL V3 Editor Owner’s Manual41C ON (MATRIX send on/off)This is an on/off switch for the signal sent from the MIX channel to the MATRIX bus.D Channel

M7CL V3 Editor Owner’s Manual42❏ EQUALIZERA LIBRARYAccesses the OUTPUT EQ page of the LIBRARY window.B ONSwitches the EQ on/off.C EQ graphIndicates th

M7CL V3 Editor Owner’s Manual43❏ DYNAMICS1Except for the fact that the available types are COMPRESSOR, EXPANDER, COMPAND H and COMPAND S, and that you

M7CL V3 Editor Owner’s Manual44If a MATRIX channel is selected❏ CHANNEL SELECT (Channel selection)Except for the fact that your editing applies to a M

M7CL V3 Editor Owner’s Manual45C ON(FROM MIX, ST/MONO send on/off)These are on/off switches for the signal sent from the MIX buses or STEREO/MONO buse

M7CL V3 Editor Owner’s Manual46❏ FaderA ONThis switches the MATRIX channel on/off.B FaderThis adjusts the output level of the MATRIX channel. A meter

M7CL V3 Editor Owner’s Manual47If a STEREO/MONO channel is selected❏ CHANNEL SELECT (Channel selection)Except for the fact that your editing applies t

M7CL V3 Editor Owner’s Manual48❏ BALANCE (except for MONO channel)This adjusts the left/right volume balance in the STEREO bus. You can set this to th

M7CL V3 Editor Owner’s Manual49Here you can edit the M7CL’s various libraries. You can also load library files that were saved on a drive of your com-p

M7CL V3 Editor Owner’s Manual 5 ❏ Creating a user key To open the Create User Key dialogbox, choose [Create User Key] from the [File] menu.This crea

M7CL V3 Editor Owner’s Manual50F FILEThis list shows the contents of the data in the library file you opened using the OPEN button (1). The list includ

M7CL V3 Editor Owner’s Manual51To do this, use the following methods to select the scene(s) that you want to copy or move.•To select a single sceneCl

M7CL V3 Editor Owner’s Manual52Here you can assign the input/output port for each channel, its direct output, and its insert-in/out.This window is div

M7CL V3 Editor Owner’s Manual53OUTPUT PATCH pageHere you can select the input port that is assigned to the output of each output channel.INPUT INSERT

M7CL V3 Editor Owner’s Manual54OUTPUT INSERT PATCH pageHere you can assign input/output ports to the insert-in/out of each output channel. Select the

M7CL V3 Editor Owner’s Manual55PATCH LIST pageHere you can view and edit the input patch and output patch settings. A Input channel numberB Input chan

M7CL V3 Editor Owner’s Manual56Here you can make settings for GEQ, effects, and external head amps.This window is divided into GEQ/EFFECT and EXTERNAL

M7CL V3 Editor Owner’s Manual57A MountSelect a GEQ module or effect module for mounting in the rack, from the following choices.B Input patchSelect th

M7CL V3 Editor Owner’s Manual58Rack module editor — GEQ windowIn this window you can select the insertion destination of GEQ, and edit the parameters.

M7CL V3 Editor Owner’s Manual59C Input patchClick the CHANNEL field, and choose one of the following as the signal route that will be patched to the in

M7CL V3 Editor Owner’s Manual 6 G ACCESS PERMISSION In this area, specify the parameters that this user will be allowed to operate. H CH OPERATION IN

M7CL V3 Editor Owner’s Manual60G ON (GEQ on/off)Switches the currently selected GEQ module on/off.H LINKThis button links the settings of two adjacent

M7CL V3 Editor Owner’s Manual61Rack module editor — Effect windowHere you can select the effect type for an internal effect, edit the parameters, and

M7CL V3 Editor Owner’s Manual62A Rack No. (Rack selection)Select the rack module that you want to control.B BYPASSThis button temporarily bypasses the

M7CL V3 Editor Owner’s Manual63J Output meterIndicates the level of the signal being output from the internal effect.K Parameter display select button

M7CL V3 Editor Owner’s Manual64EXTERNAL HA/EXT-ES HA pageThe EXT-ES HA page features VIEW switch buttons. Use these buttons to select the virtual rack

M7CL V3 Editor Owner’s Manual65This window shows the signal levels of each section in the M7CL, letting you check for the presence of signals and whet

M7CL V3 Editor Owner’s Manual66OUTPUT METER pageA METERING POINTSelect one of the following as the point where metering will occur.PRE EQ, PRE FADER,

M7CL V3 Editor Owner’s Manual67In this window you can select the channels that will be assigned to each DCA group and mute group. This window is divid

M7CL V3 Editor Owner’s Manual68MUTE GROUP ASSIGN pageHere you can specify the channels that will be assigned to mute groups 1–8. The upper part of the

M7CL V3 Editor Owner’s Manual69CHANNEL LINK pageIf you link two or more input channels, the parameters of these channels will interlock with each othe

M7CL V3 Editor Owner’s Manual7Working with SessionsAll of your console’s mix settings in M7CL Editor, including Scene and library data, are called Ses

M7CL V3 Editor Owner’s Manual70C LINK PARAMETERThis section enables you to select the parameters to interlock.(*)INPUT CH 33-48 can be viewed during o

M7CL V3 Editor Owner’s Manual71Here you can manage scene memories, and make various settings related to scene recall operations.This window is divided

M7CL V3 Editor Owner’s Manual72F FILEThis area lists the scenes in the file you opened using the OPEN button (2). The list includes the following items

M7CL V3 Editor Owner’s Manual73O INTERNAL DATAThis area shows the M7CL’s scene memory contents. The items displayed are the same as in the FILE list (

M7CL V3 Editor Owner’s Manual74RECALL SAFE pageHere you can make settings for the Recall Safe function that excludes only specific channels from recall

M7CL V3 Editor Owner’s Manual75F OUTPUT SAFE PARAMETERSIn this area you can view and edit the Recall Safe settings for all output channels. The items

M7CL V3 Editor Owner’s Manual76FADE TIME pageHere you can make settings for the Fade Time function which adjusts the time over which fader and pan wil

M7CL V3 Editor Owner’s Manual77D OUTPUT CHANNEL FADING ENABLEThese are on/off buttons that select the output channels that will be excluded from recal

M7CL V3 Editor Owner’s Manual78In this window, you can specify the functions or parameters to be assigned to the User Defined keys.INPUT CH 33-48 can b

M7CL V3 Editor Owner’s Manual79SENDS ON FADER mode enables you to adjust the send level to the MIX/MATRIX bus using the fader. In this mode, the signa

M7CL V3 Editor Owner’s Manual8Stage Box Data ConversionTo open the Stage Box Data Conversion dialog box, click the [Stage Box Data Conversion] button

M7CL V3 Editor Owner’s Manual80In the Output Port window you can assign the source channel for each output port and set the parameters. The window inc

M7CL V3 Editor Owner’s Manual81G Delay timeThe millisecond delay time value is shown above the knob.The delay time value in the units selected in the

M7CL V3 Editor Owner’s Manual82(*) It can be viewed during offline editing only if “M7CL-48” or “M7CL-48ES” is selected in the System Setup dialog box.

PM5D Editor Owner’s Manual83BBYPASS .... 62CCLEAR ... 51, 73CLEAR ALL ...

M7CL V3 Editor Owner’s Manual9B M7CL using External HA via Slot ➞ Using Internal HAConverts the patch settings as follows:(*) The same HA settings wil