Yamaha L-85S Instruction Manual

Browse online or download Instruction Manual for Storage chests & cabinets & trunks Yamaha L-85S. Yamaha L-85S Assembly Instruction User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 2
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
这些注意事项用于确保安全使用架以
防止您和他人受伤。
只要遵循这些注意事项,您便可长期安全使
用键盘支架。
请注意不要混淆任何部件,并务必以正
确方向安装所有部件。请根据下列顺序
进行组装。
至少应由
2
个人执行组装。
组装支架时,请务必使用附带的螺钉。使
用任何其它螺钉可能会造成组装不牢
固,从而导致键盘和支架损坏。
请务必在组装完成后再使用支架。若组
装未完成可能会造成支架翻倒以及键盘
的损坏。
务必将支架放在平坦、稳定的表面上。
支架放在不平的表面上可能会造成其不
稳或翻倒,从而导致键盘跌落且可能使
人员受伤。
请勿将本支架用于其设计用途之外的任
何其它用途。本支架专为指定键盘设计。
若将指定键盘以外的其它物体放在支架
上可能会造成物件跌落或支架翻倒。
请勿对键盘用力过大,否则可能会造成
支架翻倒或键盘跌落。
在使用前请确保支架稳固安全,且所有
螺钉都被拧紧。否则,支架可能会翻倒,
键盘可能会跌落,或者可能会造成使用
者受伤。
若要进行拆卸,请将上述组装步骤顺序
颠倒即可。
中文
小心
在组装或使用键盘支架前,请仔细阅读这
些注意事项。
These precautions are to promote safe
use of the stand and to prevent injury
and damage from occurring to you and
others.
By following these precautions careful-
ly, you will be able to get long and safe
usage from your keyboard stand.
Be careful not to confuse any of the
parts, and be sure to install all parts in
the correct direction. Please assemble
according to the sequence given below.
Assembly should be carried out by at
least two persons.
Use only the screws provided when as-
sembling the stand. Use of any other
screws may result in an inadequate as-
sembly that may cause damage to both
the keyboard and the stand.
Use the stand only after assembly is
complete. An incomplete assembly may
resultin overturning of the stand and
damage to the keyboard.
Always place the stand on a flat, stable
surface. Placing the stand on uneven
surfaces may result in it becoming un-
stable or overturn, causing the keyboard
to drop and possibly resulting in injury.
Do not use the stand for anything other
than its designed purpose. The stand is
not designed to hold anything other than
the specified keyboard. Placing any ob-
ject other than the specified keyboard on
the stand may result in the object drop-
ping or the stand overturning.
Do not apply excessive force to the key-
board as it may cause the stand to over-
turn or the keyboard to drop.
Make sure the stand is sturdy and safe,
and all screws have been tight and firm
before use. If not, the stand may over-
turn, the keyboard may drop, or may re-
sult in injury to the user.
To disassemble, reverse the assembly
sequence given below.
ENGLISH
CAUTION
Read these precautions carefully be-
fore you assemble or use the key-
board stand.
Die Vorsichtsmaßregeln führen wichtige
Punkte für sicheren Einsatz des Stän-
ders an und sollen Beschädigungen so-
wie Verletzungen der eigenen und
anderer Personen verhüten helfen.
Wenn Sie diese Vorsichtsmaßregeln
sorgfältig beachten, wird Ihnen der Key-
board-Ständer über Jahre hinweg sicher
und zuverlässig seinen Dienst tun.
Achten Sie darauf, die Teile nicht zu ver-
wechseln, und installieren Sie alle Teile
in der richtigen Ausrichtung. Gehen Sie
beim Zusammenbau bitte in der ange-
gebenen Reihenfolge vor.
Die Montage sollte von mindestens zwei
Personen vorgenommen werden.
Verwenden Sie für den Zusammenbau aus-
schließlich die mit dem Ständer gelieferten
Schrauben. Der Gebrauch anderer Schrauben
kann die Standfestigkeit beeinträchtigen und
eine Beschädigung des Ständers bzw. Key-
boards zur Folge haben.
Verwenden Sie den Ständer erst, nachdem
er komplett zusammengebaut wurde. Ein nur
teilweise zusammengebauter Ständer kann
kippen oder einen Fall des Keyboards bewir-
ken.
Stellen Sie den Ständer stets auf einer
soliden und ebenen Fläche auf. Auf ei-
ner unebenen Stellfläche kann der Stän-
der umkippen und einen Fall des
Keyboards, im Extremfall sogar eine
Körperverletzung, zur Folge haben.
Verwenden Sie den Ständer ausschließ-
lich für den Zwecke, für den er vorgese-
hen ist. Der Ständer eignet sich nicht für
Gegenstände, die schwerer sind als das
Keyboard. Wenn ein anderer Gegen-
stand als das vorgeschriebene Key-
board auf den Ständer gestellt wird,
besteht die Gefahr, daß er herunterfällt
oder den Ständer zum Kippen bringt.
Drücken Sie nicht zu stark auf bzw. ge-
gen das auf dem Ständer stehende Key-
board — dies könnte einen Fall des
Keyboards oder ein Kippen des Stän-
ders zur Folge haben.
Vergewissern Sie sich vor Gebrauch,
daß der Ständer ordnungsgemäß zu-
sammengebaut wurde und alle Schrau-
ben fest angezogen sind. Ein wackeliger
Ständer kann kippen oder einen Fall des
Keyboards und im Extremfall sogar eine
Verletzung zur Folge haben.
Für die Demontage muß die angegebene
Reihenfolge umgekehrt befolgt werden.
DEUTSCH
VORSICHT
Lesen Sie die folgenden Vorsichts-
maßregeln vor Zusammenbau bzw.
Gebrauch des Keyboard-Ständers
aufmerksam durch.
Ces précautions ont pour but de pro-
mouvoir l’utilisation en toute sécurité
du support et d’éviter les blessures et
dommages qui pourraient arriver aux
autres et à vous.
En suivant soigneusement ces précau-
tions, votre support de clavier vous of-
frira la sécurité et une longue durée
d’utilisation.
Veiller à ne pas mélanger les pièces et à
les installer dans le sens correct.
Veuillez assembler l’instrument dans
l’ordre indiqué ci-dessous.
La présence de deux personnes mini-
mum est nécessaire pour procéder au
montage.
Lors du montage du support, utilisez
seulement les vis fournies. L’utilisation
de toutes autres vis pourrrait résulter en
un montage qui endommagerait le cla-
vier et le support.
Utilisez le support lorsque son assem-
blage est complètement terminé. Si l’as-
semblage du support n’est pas
complètement terminé, le support risque
de se renverser ou bien le clavier risque
de tomber par terre.
Placez toujours le support sur une surfa-
ce plane et stable. Placer le support sur
une surface inégale peut provoquer son
instabilité ou son renversement, la chute
du clavier ou une blessure physique.
N’utilisez pas le support pour un usage
autre que celui pour lequel il est prévu.
Le support a été uniquement conçu pour
recevoir le clavier spécifié et aucun
autre objet. Le fait de poser des objets
autre que le clavier spécifié sur le sup-
port peut favoriser une chute de ces ob-
jets ou bien le support peut se renverser.
N’appliquez pas de force excessive sur
le clavier car cela pourrait provoquer un
renversement du support ou une chute
du clavier.
Assurez-vous que le support est stable
et sûr et que toutes les vis sont bien ser-
rées avant utilisation. Sinon, le support
pourrait se retourner et le clavier tomber
ou provoquer une blessure à l’utilisa-
teur.
Pour démonter le L-85/85S, inverser
l’ordre des instructions données ci-des-
sous.
FRANÇAIS
ATTENTION
Veuillez lire attentivement ces avertis-
sements avant de monter ou d’utiliser
le support de clavier.
Estas precauciones tienen el propósito
de emplear el soporte de forma segura y
evitar heridas y daños personales o en
otras personas.
Siguiendo con cuidado estas instruc-
ciones, el soporte de teclado le propor-
cionará un servicio prolongado y
seguro.
Observe cuidado para no confundir las
piezas, y asegúrese de montar todas
ellas en el sentido correcto. Proceda al
montaje en el orden indicado a conti-
nuación.
El montaje deberá realizarse al menos
por dos personas.
Emplee sólo los tornillos suministrados
para montar el soporte. El empleo de
otros tornillos puede ocasionar inestabi-
lidad del soporte lo cual puede causar
daños en el teclado y en el soporte.
Emplee el soporte después de haber
terminado el montaje. Un soporte in-
completo podría volcar o podría hacer
que se cayera el teclado.
Ponga siempre el soporte sobre una su-
perficie plana y estable. Si se pone el
soporte en una superficie inestable pue-
de causar problemas y caídas del so-
porte o del teclado, o daños personales.
No emplee el soporte para nada que no
sea para el propósito para el que ha sido
diseñado. El soporte no está diseñado
para soportar nada que no sea el tecla-
do especificado. Si se pone cualquier
otro objeto que no sea el teclado espe-
cificado sobre el soporte, tal objeto po-
dría caerse o podría volcar el teclado.
No aplique fuerza excesiva en el teclado
porque podría ocasionar el vuelco del
soporte o la caída del teclado.
No aplique fuerza excesiva en el teclado
porque puede causar la caída del sopor-
te o la del mismo teclado.
Asegúrese de que el soporte esté bien
fijado y seguro, y que todos los tornillos
se hayan apretado bien antes de utili-
zarlo. De lo contrario, podría caerse el
soporte con el teclado, o podría ocasio-
nar daños al usuario.
Para desmontar las unidades, invierta la
secuencia de montaje facilitada a conti-
nuación.
ESPAÑOL
ATENCIÓN
Lea atentamente estas precauciones
antes de montar o de emplear el so-
porte de teclado.
ここに 示した注意事項は、製品を 安全に正しくご使用
いただ き、お客様や他の方々への 危害や財産への損害
を未然に防止するためのものです。
必ずお守りください。
この説 明書に表示されている 記号には、次のような意
味があります。
「ご注意ください」という注意喚起を示します。
∼しないでくださいという「禁止」を示します。
「必ず実行」してくださいという強制を示します。
日本語
安全上のご注意
立作業、およびご使用の前に、必ずこの
「安全上のご注意」をお読みください。
注意
以下の内容を無視した取り扱いをすると、傷害を負
う可能性、または、物的損害が発生する可能性が想
定されます。
部品を まちがえたり、向 きをまちが えない
ように注意して、手順どおりに組み立てる。
組み立ては、必ず 2 人以上で行なう。
部品の 取り付けは、必ず 付属のネジ を使用
する。
付属の ネジ以外のネ ジを使用す ると、他の
部品を 傷つけたり、スタ ンドとして の機能
を果たさなかったりします。
スタンド / キーボードは、組み立てが完了
した状態で使用する。
未完成 の状態で使用 すると、キーボ ードが
落ちたり、スタンドが転倒して危険です。
傾斜地や不安定な場所に設置しない。
スタンド が転倒してキ ーボードが故 障した
り、お客様 がけがをした りする原因 になり
ます。
指定のキーボード以外の目的に使用しない。
指定のキ ーボード以外 のものは取り 付けら
れませ ん。また、指定のキ ーボード 以外の
ものを のせたり、スタ ンドにの ったり、ス
タンド にもたれ掛か ったりする と、のせて
いるも のが落ちたり、ス タンドが転 倒して
危険です。
スタンド の上のキーボ ードに必要以 上の力
を加えない。
スタンドが転倒したりして危険です。
使用前に安全点検をする。
使用す る前に、ネジが確 実に締まっ ている
か、必ず確 認してくだ さい。ネジが ゆるん
でいる と、スタンドが転 倒してキー ボード
が故障 したり、お客様が けがをした りする
原因になります。
スタン ドを分解する ときは、組み立 てと逆
の手順で行なう。
記号表示について
ENGLISH
Keyboard Stand Assembly
Have a Phillips-head (+) screwdriver ready.
The parts shown in the “Assembly Parts” illustration will be used. Fol-
low the assembly instructions and select the parts as needed.
DEUTSCH
Zusammenbau und Aufstellung
Sie benötigen einen Kreuzschlitzschraubendreher (+).
Es werden die in der “Bauteile”-Zeichnung a/jointfilesconvert/536033/bgebildeten Teile ver-
wendet. Folgen Sie beim Zusammenbau den Anweisungen, und wählen
Sie die jeweils benötigten Teile.
FRANÇAIS
Assemblage du support de clavier
Munissez-vous d’un tournevis Phillips (cruciforme).
Les éléments qui sont représentés sur la figure intitulée “Éléments à
assembler” seront utilisés. Veuillez vous conformer aux instructions
d’assemblage et sélectionner les éléments nécessaires.
ESPAÑOL
Conjunto del soporte del teclado
Tenga preparado un destornillador de cabeza en cruz (+).
Se usarán las partes mostradas en la ilustración de “Partes del con-
junto”. Siga las instrucciones de montaje y seleccione las partes a me-
dida que se requieran.
日本語
キーボードスタンドの組み立て方
プラス ( ) のドライバーを用意します。
すべての部品 を取り出し、部品がすべて そろっているかイラス トを参照して
確認します。
組み立て手順に従って必要な部品を使用します。
中文
键盘支架的组装
准备一把十字螺丝刀。
将用到“组装用部件”图中所示的部件。请按照组装说明进行操作并
根据需要选择部件。
Keyboard Stand / Keyboard-Ständer
Support de clavier / Soporte de teclado
キーボードスタンド
/
键盘支架
L-85/L-85S
Assembly Instructions / Montageanleitung
Instructions pour le montage / Instrucciones de montaje
組立説明書
/
组装说明书
A
BB
C 6 x 14 mm screws (6 pcs.)
C 6 x 14-mm-Schrauben (6 St.)
C Vis de 6 x 14 mm (6 pièces)
C Tornillos de 6 x 14 mm (6 uds.)
C 6 x 14 mm
ネジ
(x 6)
C
6 x 14 mm
螺钉
(6 pcs.)
D
5 x 16 mm screws (4 pcs.)
D
5 x 16-mm-Schrauben (4 St.)
D
Vis de 5 x 16 mm (4 pièces)
D
Tornillos de 5 x 16 mm (4 uds.)
D
5 x 16 mm
ネジ (
x 4
)
D
5 x 16 mm
螺钉
(4 pcs.)
Assembly Parts / Bauteile / Éléments à assembler /
Partes del conjunto /
組み立て部品
/
组装用部件
E
Anti-fall brackets (2 pcs.)
E
Kippschutzwinkel (2 St.)
E
Equerres de prévention des chutes (2 pièces)
E
Abrazaderas para evitar caídas (2 uds.)
E
転倒防止用金具
(x 2)
E
防跌落托架
(2 pcs.)
Attach these brackets when locating the keyboard away from a wall.
Bringen Sie diese Beschläge an, wenn Sie das Keyboard nicht vor einer Wand aufstellen.
Servez-vous de ces équerres lorsque le clavier est placé loin du mur.
Acople estas abrazaderas cuando coloque el teclado separado de la pared.
使使
使使
当将键盘远离墙壁放置时,安装这些托架。
F
3.5 x 16 mm screws (4 pcs.)
F
3,5 x 16-mm-Schrauben (4 St.)
F
Vis de 3,5 x 16 mm (4 pièces)
F
Tornillos de 3,5 x 16 mm (4 uds.)
F
3.5 x 16 mm
ネジ
(x 4)
F
3.5 x 16 mm
螺钉
(4 pcs.)
Page view 0
1 2

Summary of Contents

Page 1 - L-85/L-85S

这些注意事项用于确保安全使用支架以及防止您和他人受伤。只要遵循这些注意事项,您便可长期安全使用键盘支架。 ●请注意不要混淆任何部件,并务必以正确方向安装所有部件。请根据下列顺序进行组装。 ●至少应由 2 个人执行组装。 ●组装支架时,请务必使用附带的螺钉。使用任何其它螺钉可能会造成组装不牢固,从而导

Page 2

B 2-3 BB Z Attach A to B. Attach A using screws C . • Be careful not to drop the parts or touch the sharp metal fittings.• If you want to use the

Comments to this Manuals

No comments